HD64F2145BTE20 Renesas Electronics America, HD64F2145BTE20 Datasheet - Page 675
HD64F2145BTE20
Manufacturer Part Number
HD64F2145BTE20
Description
IC H8S MCU FLASH 256K 100-QFP
Manufacturer
Renesas Electronics America
Series
H8® H8S/2100r
Specifications of HD64F2145BTE20
Core Processor
H8S/2000
Core Size
16-Bit
Speed
20MHz
Connectivity
I²C, IrDA, SCI, X-Bus
Peripherals
PWM, WDT
Number Of I /o
74
Program Memory Size
256KB (256K x 8)
Program Memory Type
FLASH
Ram Size
8K x 8
Voltage - Supply (vcc/vdd)
4.5 V ~ 5.5 V
Data Converters
A/D 8x10b; D/A 2x8b
Oscillator Type
Internal
Operating Temperature
-20°C ~ 75°C
Package / Case
100-TQFP, 100-VQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-
- Current page: 675 of 847
- Download datasheet (5Mb)
6. Before branching to the programming control program (H'FFE088 *
7. Boot mode can be cleared by a reset. Cancel the reset *
8. Do not change the mode pin input levels in boot mode. If mode pin input levels are changed
9. All interrupts are disabled during programming or erasing of the flash memory.
Notes: 1. Address area for the H8S/2140B, H8S/2141B, H8S/2148B, H8S/2160B, and
switches to the programming control program. Figure 23.8 shows the on-chip RAM area in
boot mode.
LSI terminates transfer operations by the SCI_1 (by clearing the RE and TE bits in SCR to 0),
but the adjusted bit rate value remains set in BRR. Therefore, the programming control
program can still use it for transfer of write data or verify data with the host. The TxD1 pin is
in high-level output state. The contents of the CPU general registers are undefined immediately
after branching to the programming control program. These registers must be initialized at the
beginning of the programming control program, since the stack pointer (SP), in particular, is
used implicitly in subroutine calls, etc.
at least 20 states, and then setting the mode pins. Boot mode is also cleared when a WDT
overflow occurs.
from low to high during reset, operating modes are switched and the state of ports that are also
used for address output and bus control output signals (AS, RD, and HWR) are changed *
Therefore, set these pins carefully not to be output signals during reset or not to conflict with
LSI external signals.
2. Address area for the H8S/2140B, H8S/2141B, H8S/2148B, H8S/2160B, and
3. RAM address for the H8S/2140B, H8S/2141B, H8S/2148B, H8S/2160B, and
4. After reset is cancelled, mode pin input settings must satisfy the mode programming
5. The ports that also have address output functions output low as address output when
H8S/2161B. On the H8S/2145B, the address area is from H'FFD080 to H'FFD87F.
H8S/2161B. On the H8S/2145B, the address area is from H'FFD080 to H'FFD087.
H8S/2161B. On the H8S/2145B, the address is H'FFD088.
setup time (t
the mode pins are set to mode 1 during a reset. In modes other than mode 1, it enters
the high impedance state. Bus control output signals output high when the mode pins
are set to mode 1 during a reset. In modes other than mode 1, it enters the high
impedance state.
MDS
= 4 states).
Rev. 3.00 Mar 21, 2006 page 619 of 788
4
after driving the reset pin low, waiting
3
in the RAM area), this
REJ09B0300-0300
Section 23 ROM
5
.
Related parts for HD64F2145BTE20
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT STARTER FOR M16C/29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/2D
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
R0K33062P STARTER KIT
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/23 E8A
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/25
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER H8S2456 SHARPE DSPLY
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C38C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C35C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8CL3AC+LCD APPS
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR RX610
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R32C/118
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV RSK-R8C/26-29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR SH7124
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR H8SX/1622
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV FOR SH7203
Manufacturer:
Renesas Electronics America
Datasheet: