ST7FLITEUS5B6 STMicroelectronics, ST7FLITEUS5B6 Datasheet - Page 55

• Manufacturer Part Number: ST7FLITEUS5B6
• Description: MCU 8BIT 1KB FLASH 128KB 8-DIP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST7FLITEUS5B6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 5
• Program Memory Size: 1KB (1K x 8)
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-DIP (0.300", 7.62mm)
• Controller Family/series: ST7
• No. Of I/o's: 5
• Ram Memory Size: 128Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Rohs Compliant: Yes
• For Use With: 497-6403 - BOARD EVAL 8BIT MICRO + TDE1708497-6407 - BOARD EVAL FOR VACUUM CLEANER497-5861 - EVAL BRD POWER MOSFET/8PIN MCU497-5858 - EVAL BOARD PLAYBACK ST7FLITE497-5515 - EVAL BOARD PHASE CTRL DIMMER497-5049 - KIT STARTER RAISONANCE ST7FLITE497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Connectivity: -
• Other names: 497-5636-5

ST7LITEUS2, ST7LITEUS5
After this startup delay, the CPU resumes operation by servicing the AWUFH interrupt. The
AWU flag and its associated interrupt are cleared by software reading the AWUCSR
register.
To compensate for any frequency dispersion of the AWU RC oscillator, it can be calibrated
by measuring the clock frequency f
Measurement mode is enabled by setting the AWUM bit in the AWUCSR register in Run
mode. This connects f
f
Similarities with Halt mode
The following AWUFH mode behavior is the same as normal Halt mode:
●
●
●
●
Figure 26. AWUF Halt timing diagram
AWU_RC
AWUFH interrupt
f
f
AWU_RC
CPU
The MCU can exit AWUFH mode by means of any interrupt with exit from Halt
capability or a reset (see
When entering AWUFH mode, the I bit in the CC register is forced to 0 to enable
interrupts. Therefore, if an interrupt is pending, the MCU wakes up immediately.
In AWUFH mode, the main oscillator is turned off causing all internal processing to be
stopped, including the operation of the on-chip peripherals. None of the peripherals are
clocked except those which get their clock supply from another clock generator (such
as an external or auxiliary oscillator like the AWU oscillator).
The compatibility of watchdog operation with AWUFH mode is configured by the
WDGHALT option bit in the option byte. Depending on this setting, the HALT instruction
when executed while the watchdog system is enabled, can generate a watchdog reset.
to be measured using the main oscillator clock as a reference timebase.
RUN MODE
AWU_RC
Section 8.4: Active-halt and Halt
HALT MODE
to the input capture of the 8-bit lite timer, allowing the
t
AWU_RC
AWU
and then calculating the right prescaler value.
64 t
CPU
modes).
Power saving modes
RUN MODE
Clear
by software
55/136