AT91SAM9XE256-CU Atmel, AT91SAM9XE256-CU Datasheet - Page 376

• Manufacturer Part Number: AT91SAM9XE256-CU
• Description: MCU ARM9 256K FLASH 217-BGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9XE256-CU

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 180MHz
• Connectivity: EBI/EMI, Ethernet, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 96
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 56K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 217-LFBGA
• Processor Series: AT91SAMx
• Core: ARM926EJ-S
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Interface Type: 2-Wire, EBI, I2S, SPI, USART
• Maximum Clock Frequency: 180 MHz
• Number Of Programmable I/os: 96
• Number Of Timers: 6
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, KSK-AT91SAM9XE-PL, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM9XE-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 4 Channel
• Package: 217LFBGA
• Device Core: ARM926EJ-S
• Family Name: 91S
• Maximum Speed: 180 MHz
• Operating Supply Voltage: 1.8|2.5|3.3 V
• For Use With: AT91SAM9XE-EK - KIT EVAL FOR AT91SAM9XEAT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

30.4.2
30.4.2.1
30.4.2.2
6254C–ATARM–22-Jan-10
Receiver
Receiver Reset, Enable and Disable
Start Detection and Data Sampling
Figure 30-3. Baud Rate Generator
After device reset, the Debug Unit receiver is disabled and must be enabled before being used.
The receiver can be enabled by writing the control register DBGU_CR with the bit RXEN at 1. At
this command, the receiver starts looking for a start bit.
The programmer can disable the receiver by writing DBGU_CR with the bit RXDIS at 1. If the
receiver is waiting for a start bit, it is immediately stopped. However, if the receiver has already
detected a start bit and is receiving the data, it waits for the stop bit before actually stopping its
operation.
The programmer can also put the receiver in its reset state by writing DBGU_CR with the bit
RSTRX at 1. In doing so, the receiver immediately stops its current operations and is disabled,
whatever its current state. If RSTRX is applied when data is being processed, this data is lost.
The Debug Unit only supports asynchronous operations, and this affects only its receiver. The
Debug Unit receiver detects the start of a received character by sampling the DRXD signal until
it detects a valid start bit. A low level (space) on DRXD is interpreted as a valid start bit if it is
detected for more than 7 cycles of the sampling clock, which is 16 times the baud rate. Hence, a
space that is longer than 7/16 of the bit period is detected as a valid start bit. A space which is
7/16 of a bit period or shorter is ignored and the receiver continues to wait for a valid start bit.
When a valid start bit has been detected, the receiver samples the DRXD at the theoretical mid-
point of each bit. It is assumed that each bit lasts 16 cycles of the sampling clock (1-bit period)
so the bit sampling point is eight cycles (0.5-bit period) after the start of the bit. The first sampling
point is therefore 24 cycles (1.5-bit periods) after the falling edge of the start bit was detected.
Each subsequent bit is sampled 16 cycles (1-bit period) after the previous one.
MCK
AT91SAM9XE128/256/512 Preliminary
16-bit Counter
CD
OUT
0
CD
>1
1
0
Divide
by 16
Baud Rate
Receiver
Sampling Clock
Clock
376