ATMEGA64A-AU Atmel, ATMEGA64A-AU Datasheet - Page 321

• Manufacturer Part Number: ATMEGA64A-AU
• Description: MCU AVR 64K ISP FLASH 64-TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA64A-AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 53
• Program Memory Size: 64KB (32K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• Package: 64TQFP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 16 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 53
• Interface Type: SPI/USART
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 4
• Processor Series: ATMEGA64x
• Core: AVR8
• Data Ram Size: 4 KB
• Maximum Clock Frequency: 16 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• Cpu Family: ATmega
• Device Core Size: 8b
• Frequency (max): 16MHz
• Total Internal Ram Size: 4KB
• # I/os (max): 53
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 64
• Package Type: TQFP
• For Use With: 770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 27-16. JTAG Programming Instruction Set (Continued)
Note:
8160C–AVR–07/09
Instruction
8f. Read Fuses and Lock Bits
9a. Enter Signature Byte Read
9b. Load Address Byte
9c. Read Signature Byte
10a. Enter Calibration Byte Read
10b. Load Address Byte
10c. Read Calibration Byte
1. This command sequence is not required if the seven MSB are correctly set by the previous command sequence (which is
2. Repeat until o = “1”.
3. Set bits to “0” to program the corresponding fuse, “1” to unprogram the fuse.
4. Set bits to “0” to program the corresponding Lock bit, “1” to leave the Lock bit unchanged.
5. “0” = programmed, “1” = unprogrammed.
6. The bit mapping for Fuses Extended byte is listed in
7. The bit mapping for Fuses High byte is listed in
8. The bit mapping for Fuses Low byte is listed in
9. The bit mapping for Lock bits byte is listed in
10. Address bits exceeding PCMSB and EEAMSB
normally the case).
a = address high bits, b = address low bits, H = 0 - Low byte, 1 - High Byte, o = data out, i = data in, x = don’t care
TDI sequence
0111010_00000000
0111110_00000000
0110010_00000000
0110110_00000000
0110111_00000000
0000011_bbbbbbbb
0110010_00000000
0110011_00000000
0000011_bbbbbbbb
0110110_00000000
0110111_00000000
0100011_00001000
0100011_00001000
Table 27-1 on page
Table 27-5 on page
(Table 27-9
Table 27-4 on page
Table 27-3 on page
and
Table
295.
297.
297.
27-10) are don’t care.
TDO sequence
xxxxxxx_xxxxxxxx
xxxxxxx_oooooooo
xxxxxxx_oooooooo
xxxxxxx_oooooooo
xxxxxxx_oooooooo
xxxxxxx_xxxxxxxx
xxxxxxx_xxxxxxxx
xxxxxxx_oooooooo
xxxxxxx_xxxxxxxx
xxxxxxx_xxxxxxxx
xxxxxxx_oooooooo
xxxxxxx_xxxxxxxx
xxxxxxx_xxxxxxxx
296.
ATmega64A
Notes
(5)
Fuse Ext. byte
Fuse High byte
Fuse Low byte
Lock bits
321