ATA6616-P3PW Atmel, ATA6616-P3PW Datasheet - Page 191

• Manufacturer Part Number: ATA6616-P3PW
• Description: TXRX MULTICHIP MOD LIN SIP 38QFN
• Manufacturer: Atmel
• Series: AVR® ATA66 LIN-SBCr

Specifications of ATA6616-P3PW

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, LIN, SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 16
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 38-VQFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

4.16.4.5
4.16.4.6
9132D–AUTO–12/10
Enable/Disable
LIN Commands
Table 4-48.
Setting the LENA bit in LINCR register enables the LIN/UART controller. To disable the
LIN/UART controller, LENA bit must be written to 0. No wait states are implemented, so, the
disable command is taken into account immediately.
Clearing the LCMD[2] bit in LINCR register enables LIN commands.
As shown in
LINCR register are available (c.f.
Rx Header/LIN Abort Function
This function (or state) is mainly the withdrawal mode of the controller.
When the controller has to execute a master task, this state is the start point before enabling a
Tx Header command.
When the controller has only to execute slave tasks, LIN header detection/acquisition is
enabled as background function. At the end of such an acquisition (Rx Header function), auto-
matically the appropriate flags are set, and in LIN 1.3, the LINDLR register is set with the
uncoded length value.
This state is also the start point before enabling the Tx or the Rx Response command.
A running function (i.e. Tx Header, Tx or Rx Response) can be aborted by clearing LCMD[1..0]
bits in LINCR register
LABORT - in LINERR register will be set to inform the other software tasks. No wait states are
implemented, so, the abort command is taken into account immediately.
Rx Header function is responsible for:
LENA
• The BREAK field detection,
• The hardware re-synchronization analyzing the SYNCH field,
• The reception of the PROTECTED IDENTIFIER field, the parity control and the update of
• The starting of the Frame_Time_Out,
• The checking of the LIN communication integrity.
the LINDLR register in case of LIN 1.3,
0
1
LCMD[2]
0
1
x
Table 4-48 on page
LIN/UART Command List
LCMD[1]
(See ”Break-in-data” on page
0
1
0
1
0
1
x
LCMD[0]
Figure 4-72 on page
191, four functions controlled by the LCMD[1..0] bits of
0
1
0
1
0
0
1
1
x
Rx Header - LIN Abort
Disable peripheral
Atmel ATA6616/ATA6617
Rx Response
Tx Response
Byte transfer
Command
Full duplex
Tx Header
Rx Byte
Tx Byte
190).
201.). In this case, an abort flag -
(LINDLR: read only register)
LCMD[2..0]=000 after Rx
LCMD[2..0]=000 after Tx
LCMD[2..0]=000 after Tx
no CRC, no Time out
LTXDL=LRXDL=0
LIN Withdrawal
Comment
191