ATA6616-P3PW Atmel, ATA6616-P3PW Datasheet - Page 135

• Manufacturer Part Number: ATA6616-P3PW
• Description: TXRX MULTICHIP MOD LIN SIP 38QFN
• Manufacturer: Atmel
• Series: AVR® ATA66 LIN-SBCr

Specifications of ATA6616-P3PW

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, LIN, SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 16
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 38-VQFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

4.13.2.1
4.13.2.2
9132D–AUTO–12/10
Registers
Definitions
The Timer/Counter (TCNT1), Output Compare Registers (OCR1A/B), and Input Capture Reg-
ister (ICR1) are all 16-bit registers. Special procedures must be followed when accessing the
16-bit registers. These procedures are described in the section
on page
no CPU access restrictions. Interrupt requests (abbreviated to Int.Req. in the figure) signals
are all visible in the Timer Interrupt Flag Register (TIFR1). All interrupts are individually
masked with the Timer Interrupt Mask Register (TIMSK1). TIFR1 and TIMSK1 are not shown
in the figure.
The Timer/Counter can be clocked internally, via the prescaler, or by an external clock source
on the Tn pin. The Clock Select logic block controls which clock source and edge the
Timer/Counter uses to increment (or decrement) its value. The Timer/Counter is inactive when
no clock source is selected. The output from the Clock Select logic is referred to as the timer
clock (clk
The double buffered Output Compare Registers (OCR1A/B) are compared with the
Timer/Counter value at all time. The result of the compare can be used by the Waveform Gen-
erator to generate a PWM or variable frequency output on the Output Compare pins
”Output Compare Units” on page
Match Flag (OCF1A/B) which can be used to generate an Output Compare interrupt request.
The Input Capture Register can capture the Timer/Counter value at a given external (edge
triggered) event on either the Input Capture pin (ICP1) or on the Analog Comparator pins
(Section 4.19 “AnaComp - Analog Comparator” on page
a digital filtering unit (Noise Canceler) for reducing the chance of capturing noise spikes.
The TOP value, or maximum Timer/Counter value, can in some modes of operation be
defined by either the OCR1A Register, the ICR1 Register, or by a set of fixed values. When
using OCR1A as TOP value in a PWM mode, the OCR1A Register can not be used for gener-
ating a PWM output. However, the TOP value will in this case be double buffered allowing the
TOP value to be changed in run time. If a fixed TOP value is required, the ICR1 Register can
be used as an alternative, freeing the OCR1A to be used as PWM output.
The following definitions are used extensively throughout the section:
BOTTOM
MAX
TOP
136. The Timer/Counter Control Registers (TCCR1A/B) are 8-bit registers and have
T
n
).
The counter reaches the BOTTOM when it becomes 0x0000.
The counter reaches its MAXimum when it becomes 0xFFFF (decimal 65,535).
The counter reaches the TOP when it becomes equal to the highest value in the count
sequence. The TOP value can be assigned to be one of the fixed values: 0x00FF,
0x01FF, or 0x03FF, or to the value stored in the OCR
assignment is dependent of the mode of operation.
142.. The compare match event will also set the Compare
Atmel ATA6616/ATA6617
236). The Input Capture unit includes
1
A or ICR
“Accessing 16-bit Registers”
1
Register. The
See
135