AT32UC3C0128C Atmel Corporation, AT32UC3C0128C Datasheet - Page 764

• Manufacturer Part Number: AT32UC3C0128C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C0128C

• Flash (kbytes): 128 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 123
• Ext Interrupts: 144
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 7
• Twi (i2c): 3
• Uart: 5
• Can: 2
• Lin: 5
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 4
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 36
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 22
• Input Capture Channels: 12
• Pwm Channels: 20
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

29.6.1.2
29.6.1.3
29.6.1.4
32117C–AVR-08/11
Sampling method
Operating modes
Overrun mode
Table 29-2.
The bit duration is given by the formula:
Note: PRES should not be set to 0, therefore CAN clock is at least divided by 2.
Bits are sampled between PHASE_SEG1 and PHASE_SEG2. By writing the Sampling Method
bit (CANCFG.SM) to one, three samples are taken and a majority vote is performed.
Figure 29-3. Sampling by Majority Voting
Majority voting must not be used when the Prescaler field (CANCFG.PRES) is equal to zero.
CANIF has three operating modes, selectable by the Channel Mode field (CANCFG.CMODE):
When Overrun Mode is disabled, the MOb is disabled after successfully receiving a message.
This prevents overwriting the received message if a second message is received. Overrun Mode
is disabled by writing a zero to CANCFG.OVRM. Overrun Mode is disabled by default.
Sync Jump Width
PHASE_SEG2
– Normal mode (CANCFG.CMODE=00)
– Listening mode (CANCFG.CMODE=01)
– Loop back mode (CANCFG.CMODE=10)
Parameter
Prescaler
Default mode, TX and RX lines are connected to the transceiver. This mode is used
to communicate with other nodes on the bus.
The TX line is disconnected from the transceiver. The CAN channel cannot send any
message nor acknowledge when a message has been received. The channel is in
Error Passive mode and Transmit/Receive Error Counters (TEC/REC) are frozen.
This mode is used to listen to CAN bus.
The TX line is internally connected to the RX line and disconnected from the
transceiver. The CAN channel can only send messages or acknowledges to itself.
The channel is in Error Passive mode and TEC/REC are frozen. This mode is used
to detect the bit rate of the CAN bus by successive configuration of bit timing.
Tbit = (PRS + PHS1 + PHS2 + 4) x (PRES + 1) x
CAN Parameter Settings
CAN clock
Samples
[1..8]TQ
Range
[2..32]
[1..4]
Bit
PHASE_SEG1
CANCFG field
S1
PRES + 1
PHS2 + 1
SJW + 1
S2
SP
PHASE_SEG2
P
GCLK_CANIF
AT32UC3C
764