AT32UC3C0128C Atmel Corporation, AT32UC3C0128C Datasheet - Page 510

• Manufacturer Part Number: AT32UC3C0128C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C0128C

• Flash (kbytes): 128 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 123
• Ext Interrupts: 144
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 7
• Twi (i2c): 3
• Uart: 5
• Can: 2
• Lin: 5
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 4
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 36
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 22
• Input Capture Channels: 12
• Pwm Channels: 20
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

• RTY: Retry Test
• CLK: PB Clock Divider
• EAE: External Address Match Enable
• FS: Frame Size
• UNI: Unicast Hash Enable
• MTI: Multicast Hash Enable
• NBC: No Broadcast
• JFRAME: Jumbo Frames
• CAF: Copy All Frames
• BR: Bitrate
• FD: Full Duplex
• SPD: Speed
32117C–AVR-08/11
CLK
00
01
10
11
0: Normal operation.
1: The back off between collisions is always one slot time. It helps testing the too many retries condition. Also used in the pause
frame tests to reduce the pause counters decrement time from 512 bit times, to every RX_CLK cycle.
Determines by what number system clock is divided to generate Divided PB Clock (DPC). For conformance with 802.3, DPC
must not exceed 2.5MHz (DPC is only active during MDIO read and write operations).
0: External address match is disabled.
1: External address match is enabled. Eam pin can be used to copy frames to memory.
0: Reject any frames above 1518 bytes.
1: Accept frames up to 1536 bytes.
0: Unicast hash is disabled.
1: Unicast hash is enabled. Unicast frames are received when the 6-bit hash function of the destination address points to a bit
that is set in the hash register.
0: Multicast hash is disabled.
1: Multicast hash is enabled. Multicast frames are received when the 6-bit hash function of the destination address points to a bit
that is set in the hash register.
0: Frames addressed to the broadcast address of all ones are received.
1: Frames addressed to the broadcast address of all ones are not received.
0: Jumbo frames are disabled.
1: Enable jumbo frames of up to 10240 bytes to be accepted.
0: Copy all frames is disabled.
1: All valid frames are received.
0: Data is transmitted least significant nibble first.
1: Data is serialized and transmitted least significant bit first (10Mbps). Must be written before receive and transmit enable in the
network control register. Serial interface is configured with transmit and receive data being driven out on TXD[0] and received on
RXD[0] serially. Also the CRS and RX_DV are logically ORed together so either may be used as the data valid signal.
0: Full duplex mode is disabled.
1: Full duplex mode is enabled. Transmit sub-module ignores the state of collision and carrier sense and allows receive while
transmitting. Also controls the half duplex pin.
0: 10 Mbit/s speed.
1: 100 Mbit/s speed. Bit value is reflected on the SPEED pin.
DPC
PB clock divided by 8 (PB clock up to 20 MHz)
PB clock divided by 16 (PB clock up to 40 MHz)
PB clock divided by 32 (PB clock up to 80 MHz)
PB clock divided by 64 (PB clock up to 160 MHz)
AT32UC3C
510