AT32UC3C0128C Atmel Corporation, AT32UC3C0128C Datasheet - Page 275

• Manufacturer Part Number: AT32UC3C0128C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C0128C

• Flash (kbytes): 128 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 123
• Ext Interrupts: 144
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 7
• Twi (i2c): 3
• Uart: 5
• Can: 2
• Lin: 5
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 4
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 36
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 22
• Input Capture Channels: 12
• Pwm Channels: 20
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

15.9
15.9.1
Table 15-10. FGPFR Register Description
• BOD33EN: 3.3V Brown Out Detector Enable
Table 15-11. BOD33EN Field Description
• BODEN: 1.8V Brown Out Detector Enable
Table 15-12. BODEN Field Description
32117C–AVR-08/11
BOD33EN
0x0
0x1
0x2
0x3
BODEN
0x0
0x1
0x2
0x3
BODLEVEL[0]
31
23
15
7
Fuses Settings
Flash General Purpose Fuse Register (FGPFRLO)
BOD33EN
Description
BOD33 disabled
BOD33 enabled, BOD33 reset enabled
BOD33 enabled, BOD33 reset disabled
BOD33 disabled
Description
BOD18 disabled
BOD18 enabled, BOD18 reset enabled
BOD18 enabled, BOD18 reset disabled
BOD18 disabled
UPROT
30
22
14
6
The flash block contains 32 general purpose fuses. These 32 fuses can be found in the Flash
General Purpose Fuse Register Low. Some of these fuses have defined meanings outside the
flash controller and are described in this section.
In addition to the General Purpose fuses parts of the Flash, user page can have a defined mean-
ing outside the flash controller and are described in this section. Note that after writing the user
page, values will not be propagated to other modules internally on the device. Other modules
will load these values after resetting the chip.
The general purpose fuses are erased by a JTAG or aWire chip erase.
29
21
13
5
SECURE
BODEN
28
20
12
4
LOCK[15:8]
LOCK[7:0]
BODHYST
27
19
11
3
BOOTPROT
26
18
10
2
BODLEVEL[3:1]
25
17
9
1
AT32UC3C
EPFL
24
16
8
0
275