AT32UC3C0128C Atmel Corporation, AT32UC3C0128C Datasheet - Page 1231

• Manufacturer Part Number: AT32UC3C0128C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C0128C

• Flash (kbytes): 128 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 123
• Ext Interrupts: 144
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 7
• Twi (i2c): 3
• Uart: 5
• Can: 2
• Lin: 5
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 4
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 36
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 22
• Input Capture Channels: 12
• Pwm Channels: 20
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

39.6.5.1
39.6.5.2
39.6.5.3
39.6.6
39.6.6.1
Table 39-29. aWire Packet Format
32117C–AVR-08/11
Field
COMMAND/
RESPONSE
LENGTH
SYNC
DATA
CRC
Functional Description
I/O Lines
Power Management
Clocks
aWire Communication Protocol
Number of bytes
1
1
2
LENGTH
2
The pin used by AW is multiplexed with the RESET_N pin. The reset functionality is the default
function of this pin. To enable the aWire functionality on the RESET_N pin the user must enable
the AW either by sending the enable sequence over the RESET_N pin from an external aWire
master or by enabling the aWire user interface.
In 2-pin mode data is received on the RESET_N line, but transmitted on the DATAOUT line.
After sending the 2_PIN_MODE command the DATAOUT line is automatically enabled. All other
peripheral functions on this pin is disabled.
When debugging through AW the system clocks are automatically turned on to allow debugging
in sleep modes.
The aWire UART uses the internal 120 MHz RC oscillator (RC120M) as clock source for its
operation. When enabling the AW the RC120M is automatically started.
The AW is accessed through the RESET_N pin shown in
communicates through a UART operating at variable baud rate (depending on a sync pattern)
with one start bit, 8 data bits (LSB first), one stop bit, and no parity bits. The aWire protocol is
based upon command packets from an externalmaster and response packets from the slave
(AW). The master always initiates communication and decides the baud rate.
The packet contains a sync byte (0x55), a command/response byte, two length bytes (optional),
a number of data bytes as defined in the length field (optional), and two CRC bytes. If the com-
mand/response has the most significant bit set, the command/response also carries the optional
length and data fields. The CRC field is not checked if the CRC value transmitted is 0x0000.
CRC calculation
Description
Sync pattern (0x55).
Command from the master or
response from the slave.
The number of bytes in the DATA
field.
Data according to command/
response.
CRC calculated with the FCS16
polynomial.
Comment
Used by the receiver to set the baud rate
clock.
When the most significant bit is set the
command/response has a length field. A
response has the next most significant bit
set. A command does not have this bit set.
CRC value of 0x0000 makes the aWire
disregard the CRC if the master does not
support it.
Table 39-28 on page
AT32UC3C
1230. The AW
Optional
Yes
Yes
No
No
No
1231