IDT82P2816BB IDT, Integrated Device Technology Inc, IDT82P2816BB Datasheet - Page 27

• Manufacturer Part Number: IDT82P2816BB
• Description: IC LIU T1/J1/E1 16+1CH 416-PBGA
• Manufacturer: IDT, Integrated Device Technology Inc

Specifications of IDT82P2816BB

• Function: Line Interface Unit (LIU)
• Interface: E1, J1, T1
• Number Of Circuits: 1
• Voltage - Supply: 1.8V, 3.3V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: *
• Includes: Defect and Alarm Detection, Driver Over-Current Detection and Protection, LLOS Detection, PRBSARB / IB Detection and Generation
• Number Of Transceivers: 1
• Screening Level: Industrial
• Mounting: Surface Mount
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Current - Supply: -
• Power (watts): -
• Lead Free Status / RoHS Status: Not Compliant, Contains lead / RoHS non-compliant
• Other names: 82P2816BB

3.2.2
receive sensitivity.
3.2.2.1 Line Monitor
Intrusive Monitoring per T1.102 can be performed between two devices.
The monitored channel of one device is in normal operation, and the
monitoring channel of the other device taps the monitored one through a
high impedance bridging circuit (refer to Figure-9 and Figure-10).
RRINGn of the monitoring channel is dramatically attenuated. To
compensate this bridge resistive attenuation, Monitor Gain can be used
to boost the signal by 20 dB, 26 dB or 32 dB, as selected by the MG[1:0]
bits (b1~0, RCF2,...). For normal operation, the Monitor Gain should be
set to 0 dB, i.e., the Monitor Gain of the monitored channel should be 0
dB.
Partially Internal or Fully Internal Impedance Matching mode. Here the
external r or internal IM is used for voltage division, not for impedance
matching. That is, the r (IM) and the two R make up of a resistance
bridge. The resistive attenuation of this bridge is 20lg(r/(2R+r)) dB.
Channel 0 Monitoring). If multiple High-Density LIUs are used in an
application, The G.772 function of channel 0 can be used to route the
signals of channel 1~16 Receive and Transmit to channel 0 of the same
device. This channel 0 Transmit TTIP and TTRING could then be moni-
tored by another device through the Line Monitor function.
3.2.2.2 Receive Sensitivity
for which the receiver recovers data error-free with -18 dB interference
signal added.
dB.
dB.
Functional Description
IDT82P2816
The equalizer compensates high frequency attenuation to enhance
In both T1/J1 and E1 short haul applications, the Protected Non-
After the high resistance bridging circuit, the signal arriving at RTIPn/
The monitoring channel can be configured to any of the External,
Note that line monitor is only available in differential line interface.
A channel 0 monitoring function is provided (refer to Section 3.5.9
The receive sensitivity is the minimum range of receive signal level
For Receive Differential line interface, the receive sensitivity is -15
For Receive Single Ended line interface, the receive sensitivity is -12
EQUALIZER
16(+1) CHANNEL HIGH-DENSITY T1/E1/J1 LINE INTERFACE UNIT
27
connect point
connect point
R
DSX cross
DSX cross
Figure-10 Transmit Path Monitoring
R
Figure-9 Receive Path Monitoring
R
R
RRINGn
RRINGn
RRINGn
RTIPn
RTIPn
r
r
RTIPn
TTIPn
TRINGn
monitoring channel
= 20/26/32 dB
monitoring channel
= 20/26/32 dB
monitor gain
monitored channel
monitored channel
monitor gain
monitor gain
monitor gain
= 0 dB
February 6, 2009
= 0 dB