PIC18F452-I/LG Microchip Technology, PIC18F452-I/LG Datasheet - Page 138

• Manufacturer Part Number: PIC18F452-I/LG
• Description: IC MCU FLASH 16KX16 W/AD 44PLCC
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F452-I/LG

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 34
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-PLCC
• For Use With: XLT44L2 - SOCKET TRAN ICE 44PLCCDVA16XL441 - ADAPTER DEVICE ICE 44PLCC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIC18FXX2
REGISTER 15-4:
DS39564C-page 136
bit 7
bit 6
bit 5
bit 4
bit 3-0
bit 7
WCOL: Write Collision Detect bit
In Master Transmit mode:
1 = A write to the SSPBUF register was attempted while the I
0 = No collision
In Slave Transmit mode:
1 = The SSPBUF register is written while it is still transmitting the previous word (must be
0 = No collision
In Receive mode (Master or Slave modes):
This is a “don’t care” bit
SSPOV: Receive Overflow Indicator bit
In Receive mode:
1 = A byte is received while the SSPBUF register is still holding the previous byte (must
0 = No overflow
In Transmit mode:
This is a “don’t care” bit in Transmit mode
SSPEN: Synchronous Serial Port Enable bit
1 = Enables the serial port and configures the SDA and SCL pins as the serial port pins
0 = Disables serial port and configures these pins as I/O port pins
CKP: SCK Release Control bit
In Slave mode:
1 = Release clock
0 = Holds clock low (clock stretch), used to ensure data setup time
In Master mode:
Unused in this mode
SSPM3:SSPM0: Synchronous Serial Port Mode Select bits
1111 = I
1110 = I
1011 = I
1000 = I
0111 = I
0110 = I
Legend:
R = Readable bit
- n = Value at POR
SSPCON1: MSSP CONTROL REGISTER1 (I
WCOL
R/W-0
Note:
Note:
a transmission to be started (must be cleared in software)
cleared in software)
be cleared in software)
2
2
2
2
2
2
C Slave mode, 10-bit address with START and STOP bit interrupts enabled
C Slave mode, 7-bit address with START and STOP bit interrupts enabled
C Firmware Controlled Master mode (Slave IDLE)
C Master mode, clock = F
C Slave mode, 10-bit address
C Slave mode, 7-bit address
When enabled, the SDA and SCL pins must be properly configured as input or output.
Bit combinations not specifically listed here are either reserved, or implemented in
SPI mode only.
SSPOV
R/W-0
W = Writable bit
’1’ = Bit is set
SSPEN
R/W-0
OSC
R/W-0
CKP
/ (4 * (SSPADD+1))
’0’ = Bit is cleared
U = Unimplemented bit, read as ‘0’
SSPM3
R/W-0
2
C MODE)
2
SSPM2
C conditions were not valid for
R/W-0
© 2006 Microchip Technology Inc.
x = Bit is unknown
SSPM1
R/W-0
SSPM0
R/W-0
bit 0