ATA6616-P3QW Atmel, ATA6616-P3QW Datasheet - Page 268

• Manufacturer Part Number: ATA6616-P3QW
• Description: TXRX MULTICHIP MOD LIN SIP 38QFN
• Manufacturer: Atmel
• Series: AVR® ATA66 LIN-SBCr

Specifications of ATA6616-P3QW

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, LIN, SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 16
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 38-VQFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

4.23.2
T
Notes:
268
Parameters
Power Supply Current
Active Mode
(external clock)
Power Supply Current
Idle Mode
(external clock)
Power Supply Current
Power-down Mode
Analog Comparator
Input Offset Voltage
Analog Comparator
Input Leakage Current
Analog Comparator Propagation
Delay Common Mode Vcc/2
A
= –40°C to +125°C, Vcc = 2.7V to 5.5V (unless otherwise noted)
1. “Typ.”, typical values at 25°C. Maximum values are characterized values and not test limits in production.
2. “Max.” means the highest value where the pin is guaranteed to be read as low.
3. “Min.” means the lowest value where the pin is guaranteed to be read as high.
4. Although each I/O port can sink more than the test conditions (10mA at Vcc = 5V, 5mA at Vcc = 3V) under steady state con-
5. Although each I/O port can source more than the test conditions (10mA at Vcc = 5V, 5mA at Vcc = 3V) under steady state
6. Values using methods described in
7. BOD Disabled.
Atmel ATA6616/ATA6617
DC Characteristics (Continued)
ditions (non-transient), the following must be observed:
The sum of all IOL, for all ports, should not exceed 120mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
conditions (non-transient), the following must be observed:
The sum of all IOH, for all ports, should not exceed 120mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
(PRR = 0xFF) and there is no I/O drive.
(6)
(6)
(7)
Test Conditions
16MHz, Vcc = 5V
8MHz, Vcc = 5V
8MHz, Vcc = 3V
4MHz, Vcc = 3V
16MHz, Vcc = 5V
8MHz, Vcc = 5V
8MHz, Vcc = 3V
4MHz, Vcc = 3V
WDT enabled, Vcc = 5V
WDT disabled, Vcc = 5V
WDT enabled, Vcc = 3V
WDT disabled, Vcc = 3V
Vcc = 5V
V
Vcc = 5V
V
Vcc = 2.7V
Vcc = 5.0V
in
in
= Vcc/2
= Vcc/2
Section 4.6.8 “Minimizing Power Consumption” on page
Symbol
V
I
t
ACLK
ACID
I
ACIO
CC
Min.
–10
–50
Typ.
0.18
0.15
+10
170
180
5.5
2.8
1.8
3.5
1.8
0.5
10
68. Power Reduction is enabled
1
7
5
(1)
Max.
100
+40
+50
7.0
3.5
2.5
5.0
2.5
1.5
0.8
13
70
70
45
9132D–AUTO–12/10
Unit
mA
mA
mV
mA
mA
mA
mA
mA
mA
µA
µA
µA
µA
nA
ns
ns