ATSAM3S-EK Atmel, ATSAM3S-EK Datasheet - Page 760
![no-image](/images/manufacturer_photos/0/0/78/atmel_sml.jpg)
ATSAM3S-EK
Manufacturer Part Number
ATSAM3S-EK
Description
KIT EVAL FOR ATSAM3S4C
Manufacturer
Atmel
Series
SAM3Sr
Type
MCUr
Specifications of ATSAM3S-EK
Contents
Board, Cables, Power Supply
Silicon Manufacturer
Atmel
Core Architecture
ARM
Core Sub-architecture
Cortex-M3
Kit Contents
Board
Features
TFT Colour LCD Display, SD/MMC Interface
Svhc
No SVHC (15-Dec-2010)
Rohs Compliant
Yes
For Use With/related Products
*
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATSAM3S-EK
Manufacturer:
Atmel
Quantity:
135
- Current page: 760 of 1118
- Download datasheet (24Mb)
34.6.12
34.6.13
34.6.14
34.6.14.1
760
SAM3S Preliminary
External Event/Trigger Conditions
Output Controller
Quadrature Decoder Logic
Description
An external event can be programmed to be detected on one of the clock sources (XC0, XC1,
XC2) or TIOB. The external event selected can then be used as a trigger.
The EEVT parameter in TC_CMR selects the external trigger. The EEVTEDG parameter defines
the trigger edge for each of the possible external triggers (rising, falling or both). If EEVTEDG is
cleared (none), no external event is defined.
If TIOB is defined as an external event signal (EEVT = 0), TIOB is no longer used as an output
and the compare register B is not used to generate waveforms and subsequently no IRQs. In
this case the TC channel can only generate a waveform on TIOA.
When an external event is defined, it can be used as a trigger by setting bit ENETRG in
TC_CMR.
As in Capture Mode, the SYNC signal and the software trigger are also available as triggers. RC
Compare can also be used as a trigger depending on the parameter WAVSEL.
The output controller defines the output level changes on TIOA and TIOB following an event.
TIOB control is used only if TIOB is defined as output (not as an external event).
The following events control TIOA and TIOB: software trigger, external event and RC compare.
RA compare controls TIOA and RB compare controls TIOB. Each of these events can be pro-
grammed to set, clear or toggle the output as defined in the corresponding parameter in
TC_CMR.
The quadrature decoder logic is driven by TIOA0, TIOB0, TIOA1 input pins and drives the
timer/counter of channel 0 and 1. Channel 2 can be used as a time base in case of speed mea-
surement requirements (refer to
When writing 0 in the QDEN field of the TC_BMR register, the quadrature decoder logic is totally
transparent.
TIOA0 and TIOB0 are to be driven by the 2 dedicated quadrature signals from a rotary sensor
mounted on the shaft of the off-chip motor.
A third signal from the rotary sensor can be processed through pin TIOA1 and is typically dedi-
cated to be driven by an index signal if it is provided by the sensor. This signal is not required to
decode the quadrature signals PHA, PHB.
TCCLKS field of TC_CMR channels must be configured to select XC0 input (i.e. 0x101).
TC0XC0S field has no effect as soon as quadrature decoder is enabled.
Either speed or position/revolution can be measured. Position channel 0 accumulates the edges
of PHA, PHB input signals giving a high accuracy on motor position whereas channel 1 accumu-
lates the index pulses of the sensor, therefore the number of rotations. Concatenation of both
values provides a high level of precision on motion system position.
In speed mode, position cannot be measured but revolution can be measured.
Inputs from the rotary sensor can be filtered prior to down-stream processing. Accommodation
of input polarity, phase definition and other factors are configurable.
Figure 34.7 ”Timer Counter (TC) User
Interface”).
6500C–ATARM–8-Feb-11
Related parts for ATSAM3S-EK
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ATSAM3S-EK2](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
Development Boards & Kits - ARM EVAL KIT SAM3S8 & SAM3SD8 series
Manufacturer:
Atmel
Datasheet:
![ATSAM3S](/images/no-image3.png)
Part Number:
Description:
AT91 ARM Cortex M3-based Processor
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
![ATSTK600](/photos/9/20/92038/atstk600_tmb.jpg)
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
![U641B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
![U4082B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
![U4089B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
![U4255BM-M](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
![U4089B-P](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
![TDA4470](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
![ATF22V10B-25PC](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
![AT89C51ED2-IM](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
![AT24C01](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: