C8051F800DK Silicon Laboratories Inc, C8051F800DK Datasheet - Page 72
![KIT DEV C8051F800](/photos/28/94/289400/mcudevkit_sml.jpg)
C8051F800DK
Manufacturer Part Number
C8051F800DK
Description
KIT DEV C8051F800
Manufacturer
Silicon Laboratories Inc
Type
MCUr
Specifications of C8051F800DK
Contents
Board, Cables, CD, Debugger, Power Supply
Processor To Be Evaluated
C8051F800
Data Bus Width
16 bit
Interface Type
USB
Operating Supply Voltage
7 V to 15 V
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
For Use With/related Products
C8051F8xx
Lead Free Status / Rohs Status
Supplier Unconfirmed
Other names
336-1797
- Current page: 72 of 250
- Download datasheet (2Mb)
C8051F80x-83x
13.1. Configuring Port Pins as Capacitive Sense Inputs
In order for a port pin to be measured by CS0, that port pin must be configured as an analog input (see “23.
Port Input/Output” ). Configuring the input multiplexer to a port pin not configured as an analog input will
cause the capacitive sense comparator to output incorrect measurements.
13.2. Capacitive Sense Start-Of-Conversion Sources
A capacitive sense conversion can be initiated in one of seven ways, depending on the programmed state
of the CS0 start of conversion bits (CS0CF6:4). Conversions may be initiated by one of the following:
1. Writing a 1 to the CS0BUSY bit of register CS0CN
2. Timer 0 overflow
3. Timer 2 overflow
4. Timer 1 overflow
5. Convert continuously
6. Convert continuously with auto-scan enabled
Conversions can be configured to be initiated continuously through one of two methods. CS0 can be con-
figured to convert at a single channel continuously or it can be configured to convert continuously with
auto-scan enabled. When configured to convert continuously, conversions will begin after the CS0BUSY
bit in CS0CF has been set.
An interrupt will be generated if CS0 conversion complete interrupts are enabled by setting the ECSCPT
bit (EIE2.0).
Note: CS0 conversion complete interrupt behavior depends on the settings of the CS0 accumulator. If CS0 is
13.3. Automatic Scanning
CS0 can be configured to automatically scan a sequence of contiguous CS0 input channels by configuring
and enabling auto-scan. Using auto-scan with the CS0 comparator interrupt enabled allows a system to
detect a change in measured capacitance without requiring any additional dedicated MCU resources.
Auto-scan is enabled by setting the CS0 start-of-conversion bits (CS0CF6:4) to 111b. After enabling auto-
scan, the starting and ending channels should be set to appropriate values in CS0SS and CS0SE, respec-
tively. Writing to CS0SS when auto-scan is enabled will cause the value written to CS0SS to be copied into
CS0MX. After being enabled, writing a 1 to CS0BUSY will start auto-scan conversions. When auto-scan
completes the number of conversions defined in the CS0 accumulator bits (CS0CF1:0) (see “13.5. CS0
Conversion Accumulator” ), auto-scan configures CS0MX to the next highest port pin configured as an
analog input and begins a conversion on that channel. This scan sequence continues until CS0MX
reaches the ending input channel value defined in CS0SE. After one or more conversions have been taken
at this channel, auto-scan configures CS0MX back to the starting input channel. For an example system
configured to use auto-scan, please see Figure “13.2 Auto-Scan Example” on page 73.
Note: Auto-scan attempts one conversion on a CS0MX channel regardless of whether that channel’s port pin has
If auto-scan is enabled when the device enters suspend mode, auto-scan will remain enabled and running.
This feature allows the device to wake from suspend through CS0 greater-than comparator event on any
configured capacitive sense input included in the auto-scan sequence of inputs.
72
configured to accumulate multiple conversions on an input channel, a CS0 conversion complete interrupt will
be generated only after the last conversion completes.
been configured as an analog input.
Rev. 1.0
Related parts for C8051F800DK
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![500SAAB8M00000ACF](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
SMD/C°/SINGLE-ENDED OUTPUT SILICON OSCILLATOR
Manufacturer:
Silicon Laboratories Inc
![SI3210MFT](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![4010-DAAKF_868](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
N/A N/A/SI4010 AES KEYFOB DEMO WITH LCD RX
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![4010-DASKF_868](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
N/A N/A/SI4010 SIMPLIFIED KEY FOB DEMO WITH LED RX
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![4432-SEB1 C 915](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
N/A/-40 TO 85 OC/EZLINK MODULE; F930/4432 HIGH BAND (REV E/B1)
Manufacturer:
Silicon Laboratories Inc
![4432-SEB1 D 470](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
EZLink Module; F930/4432 Low Band (rev e/B1)
Manufacturer:
Silicon Laboratories Inc
![4460-TCE10D434-EK](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
I°/4460 10 DBM RADIO TEST CARD 434 MHZ
Manufacturer:
Silicon Laboratories Inc
![4461-TSQ14D868-EK](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
I°/4461 14 DBM RADIO TEST CARD 868 MHZ
Manufacturer:
Silicon Laboratories Inc
![4463-TCE20C460-EK](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
I°/4463 20 DBM RFSWITCH RADIO TEST CARD 460 MHZ
Manufacturer:
Silicon Laboratories Inc
![4463-TCE20C868-EK](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
I°/4463 20 DBM RADIO TEST CARD 868 MHZ
Manufacturer:
Silicon Laboratories Inc
![4463-TCE27F868-EK](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
I°/4463 27 DBM RADIO TEST CARD 868 MHZ
Manufacturer:
Silicon Laboratories Inc
![4463-TCE30E915S-EK](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
I°/4463 SKYWORKS 30 DBM RADIO TEST CARD 915 MHZ
Manufacturer:
Silicon Laboratories Inc
![4463-TCE30E915R-EK](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
N/A N/A/-40 TO 85 OC/4463 RFMD 30 DBM RADIO TEST CARD 915 MHZ
Manufacturer:
Silicon Laboratories Inc
![4463-TSQ20D169-EK](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
I°/4463 20 DBM RADIO TEST CARD 169 MHZ
Manufacturer:
Silicon Laboratories Inc