ATMEGA16-16AU SL602 Atmel, ATMEGA16-16AU SL602 Datasheet - Page 292

• Manufacturer Part Number: ATMEGA16-16AU SL602
• Manufacturer: Atmel

T
Notes:
2466T–AVR–07/10
A
Symbol
I
V
I
t
CC
ACLK
ACPD
ACIO
= -40°C to 85°C, V
1. “Max” means the highest value where the pin is guaranteed to be read as low
2. “Min” means the lowest value where the pin is guaranteed to be read as high
3. Although each I/O port can sink more than the test conditions (20 mA at Vcc = 5V, 10 mA at Vcc = 3V) under steady state
4. Although each I/O port can source more than the test conditions (20 mA at Vcc = 5V, 10 mA at Vcc = 3V) under steady state
conditions (non-transient), the following must be observed:
PDIP Package:
1] The sum of all IOL, for all ports, should not exceed 200 mA.
2] The sum of all IOL, for port A0 - A7, should not exceed 100 mA.
3] The sum of all IOL, for ports B0 - B7,C0 - C7, D0 - D7 and XTAL2, should not exceed 100 mA.
TQFP and QFN/MLF Package:
1] The sum of all IOL, for all ports, should not exceed 400 mA.
2] The sum of all IOL, for ports A0 - A7, should not exceed 100 mA.
3] The sum of all IOL, for ports B0 - B4, should not exceed 100 mA.
4] The sum of all IOL, for ports B3 - B7, XTAL2, D0 - D2, should not exceed 100 mA.
5] The sum of all IOL, for ports D3 - D7, should not exceed 100 mA.
6] The sum of all IOL, for ports C0 - C7, should not exceed 100 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
conditions (non-transient), the following must be observed:
PDIP Package:
1] The sum of all IOH, for all ports, should not exceed 200 mA.
2] The sum of all IOH, for port A0 - A7, should not exceed 100 mA.
3] The sum of all IOH, for ports B0 - B7,C0 - C7, D0 - D7 and XTAL2, should not exceed 100 mA.
TQFP and QFN/MLF Package:
1] The sum of all IOH, for all ports, should not exceed 400 mA.
2] The sum of all IOH, for ports A0 - A7, should not exceed 100 mA.
3] The sum of all IOH, for ports B0 - B4, should not exceed 100 mA.
4] The sum of all IOH, for ports B3 - B7, XTAL2, D0 - D2, should not exceed 100 mA.
Parameter
Power Supply Current
Power-down Mode
Analog Comparator
Input Offset Voltage
Analog Comparator
Input Leakage Current
Analog Comparator
Propagation Delay
CC
= 2.7V to 5.5V (Unless Otherwise Noted) (Continued)
(5)
Idle 4 MHz, V
WDT disabled, V
V
V
V
Condition
Active 1 MHz, V
(
Active 4 MHz, V
(
Active 8 MHz, V
(
Idle 1 MHz, V
(
(
Idle 8 MHz, V
(
WDT enabled, V
V
V
V
ATmega16
ATmega16
ATmega16
ATmega16
ATmega16
ATmega16
CC
in
CC
in
CC
CC
= V
= V
= 5V
= 5V
= 2.7V
= 4.0V
CC
CC
/2
/2
L)
L)
)
L)
L)
)
CC
CC
CC
CC
CC
CC
CC
= 3V
= 3V
= 5V
CC
= 3V
= 3V
= 5V
= 3V
= 3V
Min
-50
0.35
Typ
750
500
1.1
3.8
1.2
5.5
< 1
12
<8
ATmega16(L)
Max
15
15
40
50
5
2
7
4
Units
mA
mV
µA
nA
ns
292