PIC18F24 MICROCHIP [Microchip Technology], PIC18F24 Datasheet - Page 150

no-image

PIC18F24

Manufacturer Part Number
PIC18F24
Description
28/40-Pin High-Performance, Enhanced Flash Microcontrollers with CAN Module
Manufacturer
MICROCHIP [Microchip Technology]
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PIC18F2410-E/SO
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
PIC18F2410-I/ML
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
PIC18F2410-I/S0
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
PIC18F2410-I/SO
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
PIC18F2410-I/SP
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
PIC18F2410T-I/ML
Manufacturer:
MIC
Quantity:
1 831
Part Number:
PIC18F242-E/SP
Manufacturer:
Microchip Technology
Quantity:
135
Part Number:
PIC18F242-I/SO
Manufacturer:
SKYWORKSS
Quantity:
101
Company:
Part Number:
PIC18F242-I/SO
Quantity:
9
Company:
Part Number:
PIC18F242-I/SP
Quantity:
14
Part Number:
PIC18F2420-I/SO
Manufacturer:
MICROCHIP
Quantity:
1 560
Part Number:
PIC18F2420-I/SO
0
Part Number:
PIC18F2423-I/SP
Manufacturer:
MICROCHIP
Quantity:
1 290
17.3.5
The master can initiate the data transfer at any time
because it controls the SCK. The master determines
when the slave (Processor 2, Figure 17-2) is to
broadcast data by the software protocol.
In Master mode, the data is transmitted/received as
soon as the SSPBUF register is written to. If the SPI is
only going to receive, the SDO output could be dis-
abled (programmed as an input). The SSPSR register
will continue to shift in the signal present on the SDI pin
at the programmed clock rate. As each byte is
received, it will be loaded into the SSPBUF register as
if a normal received byte (interrupts and status bits
appropriately set). This could be useful in receiver
applications as a “Line Activity Monitor” mode.
FIGURE 17-3:
DS41159D-page 148
PIC18FXX8
Write to
SSPBUF
SCK
(CKP = 0
CKE = 0)
SCK
(CKP = 1
CKE = 0)
SCK
(CKP = 0
CKE = 1)
SCK
(CKP = 1
CKE = 1)
SDO
(CKE = 0)
SDO
(CKE = 1)
SDI
(SMP = 0)
Input
Sample
(SMP = 0)
SDI
(SMP = 1)
Input
Sample
(SMP = 1)
SSPIF
SSPSR to
SSPBUF
MASTER MODE
SPI™ MODE WAVEFORM (MASTER MODE)
bit 7
bit 7
bit 7
bit7
bit 6
bit 6
bit 5
bit 5
bit 4
bit 4
bit 3
bit 3
The clock polarity is selected by appropriately program-
ming the CKP bit (SSPCON1<4>). This then, would
give waveforms for SPI communication as shown in
Figure 17-3, Figure 17-5 and Figure 17-6, where the
MSB is transmitted first. In Master mode, the SPI clock
rate (bit rate) is user programmable to be one of the
following:
• F
• F
• F
• Timer2 output/2
This allows a maximum data rate (at 40 MHz) of
10.00 Mbps.
Figure 17-3 shows the waveforms for Master mode.
When the CKE bit is set, the SDO data is valid before
there is a clock edge on SCK. The change of the input
sample is shown based on the state of the SMP bit. The
time when the SSPBUF is loaded with the received
data is shown.
OSC
OSC
OSC
/4 (or T
/16 (or 4 • T
/64 (or 16 • T
bit 2
bit 2
CY
)
bit 1
bit 1
CY
CY
)
)
 2004 Microchip Technology Inc.
bit 0
bit 0
bit 0
bit 0
Next Q4 cycle
after Q2
4 Clock
Modes

Related parts for PIC18F24