k4r881869m Samsung Semiconductor, Inc., k4r881869m Datasheet - Page 29

• Manufacturer Part Number: k4r881869m
• Description: 288mbit Rdram 512k X 18 Bit X 2*16 Dependent Banks Direct Rdramtm
• Manufacturer: Samsung Semiconductor, Inc.

K4R881869M
Control Register Packets
Table 14 summarizes the formats of the four packet types for
control register transactions. Table 15 summarizes the fields
that are used within the packets.
Figure 25 shows the transaction format for the SETR,
CLRR, and SETF commands. These transactions consist of a
single SRQ packet, rather than four packets like the SWR
and SRD commands. The same framing sequence on the
CMD input is used, however. These commands are used
during initialization prior to any control register read or
write transactions.
a. The SETR and CLRR commands must always be applied in two successive transactions to RDRAMs; i.e. they may not be used in isolation. This is called “SETR/CLRR Reset”.
SCK
Cycle
0
1
2
3
4
5
6
7
Field
rsrv
SOP3..SOP0
SDEV5..SDEV0
SBC
SA11..SA0
SD15..SD0
SIO0 or
SIO1
for SRQ
rsrv
rsrv
rsrv
rsrv
rsrv
SDEV5
SOP3
SOP2
Description
Reserved. Should be driven as “0” by controller.
0000 - SRD. Serial read of control register {SA11..SA0} of RDRAM {SDEV5..SDEV0}.
0001 - SWR. Serial write of control register {SA11..SA0} of RDRAM {SDEV5..SDEV0}.
0010 - SETR. Set Reset bit, all control registers assume their reset values.
0100 - SETF. Set fast (normal) clock mode. 4 t
1011 - CLRR. Clear Reset bit, all control registers retain their reset values.
1111 - NOP. No serial operation.
0011, 0101-1010, 1100-1110 - RSRV. Reserved encodings.
Serial device. Compared to SDEVID5..SDEVID0 field of INIT control register field to select the RDRAM to which the transac-
tion is directed.
Serial broadcast. When set, RDRAMs ignore {SDEV5..SDEV0} for RDRAM selection.
Serial address. Selects which control register of the selected RDRAM is read or written.
Serial data. The 16 bits of data written to or read from the selected control register of the selected RDRAM.
SIO0 or
SIO1
for SA
rsrv
rsrv
rsrv
rsrv
SA11
SA10
SA9
SA8
Table 15: Field Description for Control Register Packets
SIO0 or
SIO1
for SINT
0
0
0
0
0
0
0
0
Table 14: Control Register Packet Formats
SIO0 or
SIO1
for SD
SD15
SD14
SD13
SD12
SD11
SD10
SD9
SD8
Page 27
SCYCLE
SCK
Cycle
8
9
10
11
12
13
14
15
delay until next command.
SCK
CMD
SIO0
SIO1
Figure 25: SETR, CLRR,SETF Transaction
SIO0 or
SIO1
for SRQ
SOP1
SOP0
SBC
SDEV4
SDEV3
SDEV2
SDEV1
SDEV0
1111
0000
a
T
a
16 t
SRQ packet - SETR/CLRR/SETF
SRQ packet - SETR/CLRR/SETF
4
4 t
SCYCLE
SCYCLE
SIO0 or
SIO1
for SA
SA7
SA6
SA5
SA4
SA3
SA2
SA1
SA0
The packet is repeated
00000000...00000000
from SIO0 to SIO1
delay until next command.
delay until CLRR command.
Preliminary
Direct RDRAM
Rev. 0.9 Jan. 2000
SIO0 or
SIO1
for SINT
0
0
0
0
0
0
0
0
T
20
SIO0 or
SIO1
for SD
SD7
SD6
SD5
SD4
SD3
SD2
SD1
SD0
1
0
1
0
1
0
1
0
™