dspic33fj128mc204 Microchip Technology Inc., dspic33fj128mc204 Datasheet - Page 271

• Manufacturer Part Number: dspic33fj128mc204
• Description: High-performance, 16-bit Digital Signal Controllers
• Manufacturer: Microchip Technology Inc.

22.0
The dsPIC33FJ32MC302/304, dsPIC33FJ64MCX02/
X04, and dsPIC33FJ128MCX02/X04 devices have up
to 9 ADC input channels.
The AD12B bit (AD1CON1<10>) allows each of the
ADC modules to be configured by the user as either a
10-bit, 4-sample/hold ADC (default configuration) or a
12-bit, 1-sample/hold ADC.
22.1
The 10-bit ADC configuration has the following key
features:
• Successive Approximation (SAR) conversion
• Conversion speeds of up to 1.1 Msps
• Up to nine analog input pins
• External voltage reference input pins
• Simultaneous sampling of up to four analog input
• Automatic Channel Scan mode
• Selectable conversion trigger source
• Selectable Buffer Fill modes
• Four result alignment options (signed/unsigned,
• Operation during CPU Sleep and Idle modes
The 12-bit ADC configuration supports all the above
features, except:
• In the 12-bit configuration, conversion speeds of
• There is only one sample/hold amplifier in the
Depending on the particular device pinout, the ADC
can have up to nine analog input pins, designated AN0
through AN8. In addition, there are two analog input
pins for external voltage reference connections. These
voltage reference inputs can be shared with other
analog input pins. The actual number of analog input
pins and external voltage reference input configuration
depends on the specific device.
© 2009 Microchip Technology Inc.
Note:
Note:
pins
fractional/integer)
up to 500 ksps are supported
12-bit configuration, so simultaneous sampling of
multiple channels is not supported.
10-BIT/12-BIT ANALOG-TO-
DIGITAL CONVERTER (ADC1)
Key Features
This data sheet summarizes the features
of
dsPIC33FJ64MCX02/X04,
dsPIC33FJ128MCX02/X04
devices. It is not intended to be a
comprehensive
complement the information in this data
sheet, refer to the “dsPIC33F Family
Reference
“Analog-to-Digital Converter (ADC)”
(DS70183), which is available from the
Microchip website (www.microchip.com).
The ADC module needs to be disabled
before modifying the AD12B bit.
the
Manual”,
dsPIC33FJ32MC302/304,
reference
Section
families
source.
and
16.
Preliminary
To
of
Block diagrams of the ADC module are shown in
Figure 22-1 and Figure 22-2.
22.2
The following configuration steps should be performed.
1.
2.
22.3
If more than one conversion result needs to be buffered
before triggering an interrupt, DMA data transfers can
be used. ADC1 can trigger a DMA data transfer. If
ADC1 is selected as the DMA IRQ source, a DMA
transfer occurs when the AD1IF bit gets set as a result
of an ADC1 sample conversion sequence.
The SMPI<3:0> bits (AD1CON2<5:2>) are used to
select how often the DMA RAM buffer pointer is
incremented.
The ADDMABM bit (AD1CON1<12>) determines how
the conversion results are filled in the DMA RAM buffer
area being used for ADC. If this bit is set, DMA buffers
are written in the order of conversion. The module
provides an address to the DMA channel that is the
same as the address used for the non-DMA stand-
alone buffer. If the ADDMABM bit is cleared, then DMA
buffers are written in Scatter/Gather mode. The module
provides a scatter/gather address to the DMA channel,
based on the index of the analog input and the size of
the DMA buffer.
Configure the ADC module:
a)
b)
c)
d)
e)
f)
g)
Configure ADC interrupt (if required):
a)
b)
ADC Initialization
Select
(AD1PCFGH<15:0> or AD1PCFGL<15:0>)
Select voltage reference source to match
expected
(AD1CON2<15:13>)
Select the analog conversion clock to
match desired data rate with processor
clock (AD1CON3<7:0>)
Determine how many S/H channels is used
(AD1CON2<9:8> and AD1PCFGH<15:0>
or AD1PCFGL<15:0>)
Select the appropriate sample/conversion
sequence
AD1CON3<12:8>)
Select
presented in the buffer (AD1CON1<9:8>)
Turn on ADC module (AD1CON1<15>)
Clear the AD1IF bit
Select ADC interrupt priority
ADC and DMA
port
how
range
pins
(AD1CON1<7:5>
conversion
on
as
DS70291C-page 269
analog
analog
results
inputs
inputs
and
are