ADZS-BF537-EZLITE Analog Devices, ADZS-BF537-EZLITE Datasheet - Page 13

no-image

ADZS-BF537-EZLITE

Manufacturer Part Number
ADZS-BF537-EZLITE
Description
Specifications: Type: DSP ; Contents: Evaluation Board, Software and Documentation ; For Use With/Related Products: ADSP-BF537 ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant
Manufacturer
Analog Devices
Datasheet
Frame Capture Mode
Frame capture mode allows the video source(s) to act as a slave
(for frame capture for example). The ADSP-BF534/
ADSP-BF536/ADSP-BF537 processors control when to read
from the video source(s). PPI_FS1 is an HSYNC output and
PPI_FS2 is a VSYNC output.
Output Mode
Output mode is used for transmitting video or other data with
up to three output frame syncs. Typically, a single frame sync is
appropriate for data converter applications, whereas two or
three frame syncs could be used for sending video with hard-
ware signaling.
ITU-R 656 Mode Descriptions
The ITU-R 656 modes of the PPI are intended to suit a wide
variety of video capture, processing, and transmission applica-
tions. Three distinct submodes are supported:
Active Video Mode
Active video only mode is used when only the active video por-
tion of a field is of interest and not any of the blanking intervals.
The PPI does not read in any data between the end of active
video (EAV) and start of active video (SAV) preamble symbols,
or any data present during the vertical blanking intervals. In this
mode, the control byte sequences are not stored to memory;
they are filtered by the PPI. After synchronizing to the start of
Field 1, the PPI ignores incoming samples until it sees an SAV
code. The user specifies the number of active video lines per
frame (in PPI_COUNT register).
Vertical Blanking Interval Mode
In this mode, the PPI only transfers vertical blanking interval
(VBI) data.
Entire Field Mode
In this mode, the entire incoming bit stream is read in through
the PPI. This includes active video, control preamble sequences,
and ancillary data that may be embedded in horizontal and ver-
tical blanking intervals. Data transfer starts immediately after
synchronization to Field 1. Data is transferred to or from the
synchronous channels through eight DMA engines that work
autonomously from the processor core.
DYNAMIC POWER MANAGEMENT
The ADSP-BF534/ADSP-BF536/ADSP-BF537 processors pro-
vide five operating modes, each with a different performance
and power profile. In addition, dynamic power management
provides the control functions to dynamically alter the proces-
sor core supply voltage, further reducing power dissipation.
Control of clocking to each of the peripherals also reduces
power consumption. See
settings for each mode. Also, see
Table
1. Active video only mode
2. Vertical blanking only mode
3. Entire field mode
17.
Table 4
Table
for a summary of the power
16,
Table 15
and
Rev. I | Page 13 of 68 | July 2010
Full-On Operating Mode—Maximum Performance
In the full-on mode, the PLL is enabled and is not bypassed,
providing capability for maximum operational frequency. This
is the power-up default execution state in which maximum per-
formance can be achieved. The processor core and all enabled
peripherals run at full speed.
Active Operating Mode—Moderate Dynamic Power
Savings
In the active mode, the PLL is enabled but bypassed. Because the
PLL is bypassed, the processor’s core clock (CCLK) and system
clock (SCLK) run at the input clock (CLKIN) frequency. In this
mode, the CLKIN to CCLK multiplier ratio can be changed,
although the changes are not realized until the full-on mode is
entered. DMA access is available to appropriately configured
L1 memories.
In the active mode, it is possible to disable the PLL through the
PLL control register (PLL_CTL). If disabled, the PLL must be
re-enabled before transitioning to the full-on or sleep modes.
Sleep Operating Mode—High Dynamic Power Savings
The sleep mode reduces dynamic power dissipation by disabling
the clock to the processor core (CCLK). The PLL and system
clock (SCLK), however, continue to operate in this mode. Typi-
cally an external event or RTC activity wakes up the processor.
When in the sleep mode, asserting wake-up causes the processor
to sense the value of the BYPASS bit in the PLL control register
(PLL_CTL). If BYPASS is disabled, the processor transitions to
the full on mode. If BYPASS is enabled, the processor transi-
tions to the active mode.
System DMA access to L1 memory is not supported in
sleep mode.
Table 4. Power Settings
Deep Sleep Operating Mode—Maximum Dynamic Power
Savings
The deep sleep mode maximizes dynamic power savings by dis-
abling the clocks to the processor core (CCLK) and to all
synchronous peripherals (SCLK). Asynchronous peripherals,
such as the RTC, may still be running but cannot access internal
resources or external memory. This powered-down mode can
only be exited by assertion of the reset interrupt (RESET) or by
an asynchronous interrupt generated by the RTC. When in deep
sleep mode, an RTC asynchronous interrupt causes the
ADSP-BF534/ADSP-BF536/ADSP-BF537
Mode
Full On
Active
Sleep
Deep
Sleep
Hibernate Disabled —
PLL
Enabled
Enabled/
Disabled
Enabled
Disabled —
PLL
Bypassed
No
Yes
Core
Clock
(CCLK)
Enabled Enabled On
Enabled Enabled On
Disabled Enabled On
Disabled Disabled On
Disabled Disabled Off
System
Clock
(SCLK)
Internal
Power
(V
DDINT
)

Related parts for ADZS-BF537-EZLITE