ADZS-BF537-EZLITE Analog Devices, ADZS-BF537-EZLITE Datasheet - Page 12

• Manufacturer Part Number: ADZS-BF537-EZLITE
• Description: Specifications: Type: DSP ; Contents: Evaluation Board, Software and Documentation ; For Use With/Related Products: ADSP-BF537 ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant
• Manufacturer: Analog Devices

ADSP-BF534/ADSP-BF536/ADSP-BF537
PORTS
The ADSP-BF534/ADSP-BF536/ADSP-BF537 processors
group the many peripheral signals to four ports—Port F, Port G,
Port H, and Port J. Most of the associated pins are shared by
multiple signals. The ports function as multiplexer controls.
Eight of the pins (Port F7–0) offer high source/high sink current
capabilities.
General-Purpose I/O (GPIO)
The processors have 48 bidirectional, general-purpose I/O
(GPIO) pins allocated across three separate GPIO modules—
PORTFIO, PORTGIO, and PORTHIO, associated with Port F,
Port G, and Port H, respectively. Port J does not provide GPIO
functionality. Each GPIO-capable pin shares functionality with
other processor peripherals via a multiplexing scheme; however,
the GPIO functionality is the default state of the device upon
power-up. Neither GPIO output or input drivers are active by
default. Each general-purpose port pin can be individually con-
trolled by manipulation of the port control, status, and interrupt
registers:
• Programmable Rx address filters, including a 64-bit
• Advanced power management supporting unattended
• System wake-up from sleep operating mode upon magic
• Support for 802.3Q tagged VLAN frames.
• Programmable MDC clock rate and preamble suppression.
• In RMII operation, 7 unused pins can be configured as
• GPIO direction control register – Specifies the direction of
• GPIO control and status registers – The processors employ
• GPIO interrupt mask registers – The two GPIO interrupt
address hash table for multicast and/or unicast frames, and
programmable filter modes for broadcast, multicast, uni-
cast, control, and damaged frames.
transfer of Rx and Tx frames and status to/from external
memory via DMA during low power sleep mode.
packet or any of four user-definable wake-up frame filters.
GPIO pins for other purposes.
each individual GPIO pin as input or output.
a “write one to modify” mechanism that allows any combi-
nation of individual GPIO pins to be modified in a single
instruction, without affecting the level of any other GPIO
pins. Four control registers are provided. One register is
written in order to set pin values, one register is written in
order to clear pin values, one register is written in order to
toggle pin values, and one register is written in order to
specify a pin value. Reading the GPIO status register allows
software to interrogate the sense of the pins.
mask registers allow each individual GPIO pin to function
as an interrupt to the processor. Similar to the two GPIO
control registers that are used to set and clear individual
pin values, one GPIO interrupt mask register sets bits to
enable interrupt function, and the other GPIO interrupt
mask register clears bits to disable interrupt function.
Rev. I | Page 12 of 68 | July 2010
PARALLEL PERIPHERAL INTERFACE (PPI)
The processor provides a parallel peripheral interface (PPI) that
can connect directly to parallel ADC and DAC converters, video
encoders and decoders, and other general-purpose peripherals.
The PPI consists of a dedicated input clock pin, up to three
frame synchronization pins, and up to 16 data pins. The input
clock supports parallel data rates up to half the system clock rate
and the synchronization signals can be configured as either
inputs or outputs.
The PPI supports a variety of general-purpose and ITU-R 656
modes of operation. In general-purpose mode, the PPI provides
half-duplex, bidirectional data transfer with up to 16 bits of
data. Up to three frame synchronization signals are also pro-
vided. In ITU-R 656 mode, the PPI provides half-duplex
bidirectional transfer of 8- or 10-bit video data. Additionally,
on-chip decode of embedded start-of-line (SOL) and start-of-
field (SOF) preamble packets is supported.
General-Purpose Mode Descriptions
The general-purpose modes of the PPI are intended to suit a
wide variety of data capture and transmission applications.
Three distinct submodes are supported:
Input Mode
Input mode is intended for ADC applications, as well as video
communication with hardware signaling. In its simplest form,
PPI_FS1 is an external frame sync input that controls when to
read data. The PPI_DELAY MMR allows for a delay (in
PPI_CLK cycles) between reception of this frame sync and the
initiation of data reads. The number of input data samples is
user programmable and defined by the contents of the
PPI_COUNT register. The PPI supports 8-bit and 10-bit
through 16-bit data, programmable in the PPI_CONTROL
register.
• GPIO interrupt sensitivity registers – The two GPIO inter-
1. Input mode – Frame syncs and data are inputs into the PPI.
2. Frame capture mode – Frame syncs are outputs from the
3. Output mode – Frame syncs and data are outputs from the
GPIO pins defined as inputs can be configured to generate
hardware interrupts, while output pins can be triggered by
software interrupts.
rupt sensitivity registers specify whether individual pins are
level- or edge-sensitive and specify—if edge-sensitive—
whether just the rising edge or both the rising and falling
edges of the signal are significant. One register selects the
type of sensitivity, and one register selects which edges are
significant for edge-sensitivity.
PPI, but data are inputs.
PPI.