DF2211NP24V Renesas Technology / Hitachi Semiconductor, DF2211NP24V Datasheet - Page 135
![no-image](/images/no-image-200.jpg)
DF2211NP24V
Manufacturer Part Number
DF2211NP24V
Description
H8S/2200 Series, 2212 Group, USB, RTC, HSS TNP-64B; Vcc= 2.7 to 3.6 volts, Temp= -20 to 75 C; Package: PVQN0064LB-A
Manufacturer
Renesas Technology / Hitachi Semiconductor
Datasheet
1.DF2211NP24V.pdf
(756 pages)
- Current page: 135 of 756
- Download datasheet (5Mb)
4.1
As table 4.1 indicates, exception handling may be caused by a reset, trace, trap instruction, or
interrupt. Exception handling is prioritized as shown in table 4.1. If two or more exceptions occur
simultaneously, they are accepted and processed in order of priority. Exception sources, the stack
structure, and operation of the CPU vary depending on the interrupt control mode. For details on
the interrupt control mode, refer to section 5, Interrupt Controller.
Table 4.1
Note:
4.2
Different vector addresses are assigned to different exception sources. Table 4.2 lists the exception
sources and their vector addresses. Since the usable modes differ depending on the product, for
details on each product, refer to section 3, MCU Operating Modes.
Priority
High
Low
*
Exception Handling Types and Priority
Exception Sources and Exception Vector Table
Supported only by the H8S/2218 Group.
Exception Type
Reset
Trace
Interrupt
Trap instruction
(TRAPA)
Exception Types and Priority
Section 4 Exception Handling
Start of Exception Handling
Starts immediately after a low-to-high transition at the RES or
MRES* pin, or when the watchdog timer overflows. The CPU
enters the reset state when the RES pin is low. The CPU enters
the manual reset state when the MRES pin* is low.
Starts when execution of the current instruction or exception
handling ends, if the trace (T) bit in the EXR is set to 1. This is
enabled only in trace interrupt control mode 2. Trace exception
processing is not performed after RTE instruction execution.
Starts when execution of the current instruction or exception
handling ends, if an interrupt request has been issued. Note that
after executing the ANDC, ORC, XORC, or LDC instruction or at
the completion of reset exception processing, no interrupt is
detected.
Started by execution of a trap instruction (TRAPA). Trap exception
processing is always accepted in program execution state.
Rev.7.00 Dec. 24, 2008 Page 81 of 698
REJ09B0074-0700
Related parts for DF2211NP24V
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![DF22-2S-7.92C(28)](/photos/3/92/39284/df22-2s-7_92c_28__tmb.jpg)
Part Number:
Description:
CONN SOCKET 2POS 7.92MM WHITE
Manufacturer:
Hirose Electric Co Ltd
Datasheet:
![DF22-4S-7.92C(28)](/photos/4/5/40567/df22-4s-7_92c_28__tmb.jpg)
Part Number:
Description:
CONN SOCKET 4POS 7.92MM WHITE
Manufacturer:
Hirose Electric Co Ltd
Datasheet:
![DF22-5S-7.92C(28)](/photos/4/5/40591/df22-5s-7_92c_28__tmb.jpg)
Part Number:
Description:
CONN SOCKET 5POS 7.92MM WHITE
Manufacturer:
Hirose Electric Co Ltd
Datasheet:
![DF22-3S-7.92C(28)](/photos/4/6/40601/df22-3s-7_92c_tmb.jpg)
Part Number:
Description:
CONN SOCKET 3POS 7.92MM WHITE
Manufacturer:
Hirose Electric Co Ltd
Datasheet:
![DF22-5S-7.92C](/photos/4/5/40591/df22-5s-7_92c_28__tmb.jpg)
Part Number:
Description:
CONN SOCKET 5POS 7.92MM WHITE
Manufacturer:
Hirose Electric Co Ltd
Datasheet:
![DF22-2S-7.92C](/images/manufacturer_photos/0/3/300/hirose_electric_co_ltd_tmb.jpg)
Part Number:
Description:
CONN SOCKET 2POS 7.92MM WHITE
Manufacturer:
Hirose Electric Co Ltd
Datasheet:
![DF22-3S-7.92C](/photos/4/6/40601/df22-3s-7_92c_tmb.jpg)
Part Number:
Description:
CONN SOCKET 3POS 7.92MM WHITE
Manufacturer:
Hirose Electric Co Ltd
Datasheet:
![DF22-4S-7.92C](/photos/4/5/40567/df22-4s-7_92c_28__tmb.jpg)
Part Number:
Description:
CONN SOCKET 4POS 7.92MM WHITE
Manufacturer:
Hirose Electric Co Ltd
Datasheet:
![DF22-2P-7.92DS(05)](/photos/11/12/111206/df22-2p-7_92ds_tmb.jpg)
Part Number:
Description:
CONN HEADER 2POS 7.92MM R/A TIN
Manufacturer:
Hirose Electric Co Ltd
Datasheet:
![DF22-4P-7.92DS(05)](/photos/11/13/111383/df22-4p-7_92ds_tmb.jpg)
Part Number:
Description:
CONN HEADER 4POS 7.92MM R/A TIN
Manufacturer:
Hirose Electric Co Ltd
Datasheet:
![16C6N5](/images/no-image3.png)
Part Number:
Description:
Renesas MCU
Manufacturer:
Renesas Technology / Hitachi Semiconductor
Datasheet:
![16C6NL](/images/no-image3.png)
Part Number:
Description:
Renesas MCU
Manufacturer:
Renesas Technology / Hitachi Semiconductor
Datasheet:
![M50224FP](/images/no-image3.png)
Part Number:
Description:
1.5 Channel Motor Driver with DC/DC Control
Manufacturer:
Renesas Technology / Hitachi Semiconductor
![HS2633ECH61H](/images/no-image3.png)
Part Number:
Description:
Accessories, Interface Cable
Manufacturer:
Renesas Technology / Hitachi Semiconductor
Datasheet: