STM32W108CZ STMicroelectronics, STM32W108CZ Datasheet - Page 153
STM32W108CZ
Manufacturer Part Number
STM32W108CZ
Description
High-performance, IEEE 802.15.4 wireless system-on-chip with embedded Flash memory
Manufacturer
STMicroelectronics
Datasheet
1.STM32W108CC.pdf
(232 pages)
Specifications of STM32W108CZ
Receive Current (w/ Cpu)
27 mA
Transmit Current (w/ Cpu, +3 Dbm Tx)
31 mA
Low Deep Sleep Current, With Retained Ram And Gpio
400 nA/800 nA with/without sleep timer
Standard Arm Debug Capabilities
Flash patch & breakpoint; data watchpoint & trace; instrumentation trace macrocell
Single Voltage Operation
2.1-3.6 V with internal 1.8 V and 1.25 V regulators
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 153 of 232
- Download datasheet (6Mb)
STM32W108HB STM32W108CC STM32W108CB STM32W108CZ
10.3.2
Table 89.
31
15
30
14
Bits [6:4]
Timer x control register 2 (TIMx_CR2)
Address offset: 0xE004 (TIM1) and 0xF004 (TIM2)
Reset value:
Timer x control register 2 (TIMx_CR2)
Bit 7
29
13
TIM_TI1S: TI1 Selection
0: TI1M (input of the digital filter) is connected to TI1 input.
1: TI1M is connected to the TI_HALL inputs (XOR combination).
TIM_MMS: Master Mode Selection
This selects the information to be sent in master mode to a slave timer for synchronization
using the trigger output (TRGO).
000: Reset - the TIM_UG bit in the TMRx_EGR register is trigger output.
If the reset is generated by the trigger input (slave mode controller configured in reset mode),
then the signal on TRGO is delayed compared to the actual reset.
001: Enable - counter enable signal CNT_EN is trigger output.
This mode is used to start both timers at the same time or to control a window in which a slave
timer is enabled. The counter enable signal is generated by either the TIM_CEN control bit or
the trigger input when configured in gated mode. When the counter enable signal is controlled
by the trigger input there is a delay on TRGO except if the master/slave mode is selected (see
the TIM_MSM bit description in TMRx_SMCR register).
010: Update - update event is trigger output.
This mode allows a master timer to be a prescaler for a slave timer.
011: Compare Pulse.
The trigger output sends a positive pulse when the TIM_CC1IF flag is to be set (even if it was
already high) as soon as a capture or a compare match occurs.
100: Compare - OC1REF signal is trigger output.
101: Compare - OC2REF signal is trigger output.
110: Compare - OC3REF signal is trigger output.
111: Compare - OC4REF signal is trigger output.
28
12
Reserved
27
11
0x0000 0000
26
10
25
9
Doc ID 16252 Rev 13
24
8
Reserved
TIM_TI
1S
23
rw
7
22
6
TIM_MMS
rw
21
5
20
4
General-purpose timers
19
3
18
2
Reserved
17
1
153/232
16
0
Related parts for STM32W108CZ
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
16/32-BITS MICROS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Starter and extension kits for STM32W108xx microcontrollers
Manufacturer:
STMICROELECTRONICS [STMicroelectronics]
Datasheet:
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search ---> STE53NA50
Manufacturer:
STMicroelectronics
Datasheet: