SAM3A4C Atmel Corporation, SAM3A4C Datasheet - Page 329
SAM3A4C
Manufacturer Part Number
SAM3A4C
Description
Manufacturer
Atmel Corporation
- Current page: 329 of 1465
- Download datasheet (26Mb)
21.4.3.1
21.4.3.2
21.4.4
11057A–ATARM–17-Feb-12
11057A–ATARM–17-Feb-12
In Application Programming (IAP) Feature
Enumeration Process
Communication Endpoints
The USB protocol is a master/slave protocol. This is the host that starts the enumeration send-
ing requests to the device through the control endpoint. The device handles standard requests
as defined in the USB Specification.
Table 21-2.
The device also handles some class requests defined in the CDC class.
Table 21-3.
Unhandled requests are STALLed.
There are two communication endpoints and endpoint 0 is used for the enumeration process.
Endpoint 1 is a 64-byte Bulk OUT endpoint and endpoint 2 is a 64-byte Bulk IN endpoint. SAM-
BA Boot commands are sent by the host through endpoint 1. If required, the message is split by
the host into several data payloads by the host driver.
If the command requires a response, the host can send IN transactions to pick up the response.
The IAP feature is a function located in ROM that can be called by any software application.
When called, this function sends the desired FLASH command to the EEFC and waits for the
Flash to be ready (looping while the FRDY bit is not set in the MC_FSR register).
Since this function is executed from ROM, this allows Flash programming (such as sector write)
to be done by code running in Flash.
The IAP function entry point is retrieved by reading the NMI vector in ROM (0x00800008).
This function takes one argument in parameter: the command to be sent to the EEFC.
This function returns the value of the MC_FSR register.
Request
GET_DESCRIPTOR
SET_ADDRESS
SET_CONFIGURATION
GET_CONFIGURATION
GET_STATUS
SET_FEATURE
CLEAR_FEATURE
Request
SET_LINE_CODING
GET_LINE_CODING
SET_CONTROL_LINE_STATE
Handled Standard Requests
Handled Class Requests
Definition
Returns the current device configuration value.
Sets the device address for all future device access.
Sets the device configuration.
Returns the current device configuration value.
Returns status for the specified recipient.
Set or Enable a specific feature.
Clear or Disable a specific feature.
Definition
Configures DTE rate, stop bits, parity and number of
character bits.
Requests current DTE rate, stop bits, parity and number
of character bits.
RS-232 signal used to tell the DCE device the DTE
device is now present.
SAM3X/A
SAM3X/A
329
329
Related parts for SAM3A4C
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
AT91SAM ARM-based Flash MCU
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: