SAM3A4C Atmel Corporation, SAM3A4C Datasheet - Page 1073
SAM3A4C
Manufacturer Part Number
SAM3A4C
Description
Manufacturer
Atmel Corporation
- Current page: 1073 of 1465
- Download datasheet (26Mb)
39.5.1.3
11057A–ATARM–17-Feb-12
11057A–ATARM–17-Feb-12
Interrupts
Figure 39-5. General States
After a hardware reset, the UOTGHS is in the Reset state. In this state:
After writing a one to UOTGHS_CTRL.USBE, the UOTGHS enters the Device or the Host mode
(according to the ID detection) in idle state.
The UOTGHS can be disabled at any time by writing a zero to UOTGHS_CTRL.USBE. In fact,
writing a zero to UOTGHS_CTRL.USBE acts as a hardware reset, except that the
UOTGHS_CTRL.OTGPADE, UOTGHS_CTRL.VBUSPO, UOTGHS_CTRL.FRZCLK,
UOTGHS_CTRL.UIDE, UOTGHS_CTRL.UIMOD and, UOTGHS_DEVCTRL.LS bits are not
reset.
One interrupt vector is assigned to the USB interface.
structure of the USB interrupt system.
• The macro is disabled. The UOTGHS Enable bit in the General Control register
• The macro clock is stopped in order to minimize the power consumption. The Freeze USB
• The UTMI is in suspend mode.
• The internal states and registers of the device and host modes are reset.
• The DPRAM is not cleared and is accessible.
• The UOTGHS_SR.ID and UOTGHS_SR.VBUS bits reflect the states of the UOTGID and
• The OTG Pad Enable (UOTGHS_CTRL.OTGPADE) bit, the VBus Polarity
(UOTGHS_CTRL.USBE) is zero.
Clock bit (UOTGHS_CTRL.FRZCLK) is set.
VBUS input pins.
(UOTGHS_CTRL.VBUSPO) bit, the UOTGHS_CTRL.FRZCLK bit, the
UOTGHS_CTRL.USBE bit, the UOTGID Pin Enable (UOTGHS_CTRL.UIDE) bit, the
UOTGHS Mode (UOTGHS_CTRL.UIMOD) bit, and the Low-Speed Mode Force
(UOTGHS_DEVCTRL.LS) bit can be written by software, so that the user can program pads
and speed before enabling the macro, but their value is only taken into account once the
macro is enabled and unfrozen.
UOTGHS_CTRL.FRZCLK = 1
UOTGHS_CTRL.USBE = 0
Clock stopped:
UOTGHS_CTRL.USBE = 1
Macro off:
Device
ID = 1
UOTGHS_CTRL.USBE = 0
UOTGHS_CTRL.USBE = 1
UOTGHS_CTRL.USBE = 0
Reset
ID = 0
Figure 39-6 on page 1074
UOTGHS_CTRL_USBE = 0
Host
RESET
HW
<any
other
state>
SAM3X/A
SAM3X/A
shows the
1073
1073
Related parts for SAM3A4C
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
AT91SAM ARM-based Flash MCU
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: