AT32UC3C164C Atmel Corporation, AT32UC3C164C Datasheet - Page 620

• Manufacturer Part Number: AT32UC3C164C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C164C

• Flash (kbytes): 64 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 81
• Ext Interrupts: 100
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 7
• Twi (i2c): 3
• Uart: 5
• Can: 2
• Lin: 5
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 4
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 20
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 22
• Input Capture Channels: 12
• Pwm Channels: 19
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

25.6.14
32117C–AVR-08/11
Bus Idle Time-out
If the LIN bus is inactive for a certain duration, the slave nodes shall automatically enter in sleep
mode. In the LIN 2.0 specification, this time-out is fixed at 4 seconds. In the LIN 1.3 specifica-
tion, it is fixed at 25000 Tbits.
In Slave Node configuration, the Receiver Time-out detects an idle condition on the RXD line.
When a time-out is detected, the bit TIMEOUT in the Channel Status Register (CSR) rises and
can generate an interrupt, thus indicating to the driver to go into sleep mode.
The time-out delay period (during which the receiver waits for a new character) is programmed
in the TO field of the Receiver Time-out Register (RTOR). If the TO field is programmed at 0, the
Receiver Time-out is disabled and no time-out is detected. The TIMEOUT bit in CSR remains at
0. Otherwise, the receiver loads a 17-bit counter with the value programmed in TO. This counter
is decremented at each bit period and reloaded each time a new character is received. If the
counter reaches 0, the TIMEOUT bit in the Status Register rises.
If STTTO is performed, the counter clock is stopped until a first character is received.
If RETTO is performed, the counter starts counting down immediately from the value TO.
Table 25-15. Receiver Time-out programming
LIN Specification
2.0
1.3
19 200 bit/s
20 000 bit/s
Baud Rate
1 000 bit/s
2 400 bit/s
9 600 bit/s
-
Time-out period
25 000 Tbits
4s
AT32UC3C
38 400
76 800
80 000
25 000
4 000
9 600
TO
620