AT32UC3C164C Atmel Corporation, AT32UC3C164C Datasheet - Page 345

• Manufacturer Part Number: AT32UC3C164C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C164C

• Flash (kbytes): 64 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 81
• Ext Interrupts: 100
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 7
• Twi (i2c): 3
• Uart: 5
• Can: 2
• Lin: 5
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 4
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 20
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 22
• Input Capture Channels: 12
• Pwm Channels: 19
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

• DBW: Data Bus Width
• BAT: Byte Access Type
• EXNWMODE: External WAIT Mode
• WRITEMODE: Write Mode
32117C–AVR-08/11
EXNWMODE
DBW
BAT
This field is used only if DBW defines a 16-bit data bus.
The NWAIT signal is used to extend the current read or write signal. It is only taken into account during the pulse phase of the
read and write controlling signal. When the use of NWAIT is enabled, at least one cycle hold duration must be programmed for
the read and write controlling signal.
1: The write operation is controlled by the NWE signal. If TDF optimization is enabled (TDFMODE =1), TDF wait states will be
inserted after the setup of NWE.
0: The write operation is controlled by the NCS signal. If TDF optimization is enabled (TDFMODE =1), TDF wait states will be
inserted after the setup of NCS.
0
1
2
3
0
1
2
3
0
1
External NWAIT Mode
Disabled:
the NWAIT input signal is ignored on the corresponding chip select.
Reserved
Frozen Mode:
if asserted, the NWAIT signal freezes the current read or write cycle. after deassertion, the read or write cycle
is resumed from the point where it was stopped.
Ready Mode:
the NWAIT signal indicates the availability of the external device at the end of the pulse of the controlling read
or write signal, to complete the access. If high, the access normally completes. If low, the access is extended
until NWAIT returns high.
Data Bus Width
8-bit bus
16-bit bus
Reserved
Reserved
Byte Access Type
Byte select access type:
Write operation is controlled using NCS, NWE, NBS0, NBS1
Read operation is controlled using NCS, NRD, NBS0, NBS1
Byte write access type:
Write operation is controlled using NCS, NWR0, NWR1
Read operation is controlled using NCS and NRD
AT32UC3C
345