AT32UC3C1512C Atmel Corporation, AT32UC3C1512C Datasheet - Page 82

• Manufacturer Part Number: AT32UC3C1512C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C1512C

• Flash (kbytes): 512 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 81
• Ext Interrupts: 100
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 7
• Twi (i2c): 3
• Uart: 5
• Can: 2
• Lin: 5
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 4
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 68
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 22
• Input Capture Channels: 12
• Pwm Channels: 19
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

8.4.2
8.4.3
8.4.4
8.5
8.5.1
32117C–AVR-08/11
Functional Description
Interrupt
Debug Operation
Clocks
Oscillator Operation
The SCIF interrupt line is connected to one of the internal sources of the interrupt controller.
Using the SCIF interrupt requires the interrupt controller to be programmed first.
The SCIF module does not interact with debug operations.
The SCIF controls all oscillators on the part. Those oscillators can then be used as sources for
for generic clocks (handled by the SCIF) and for the CPU and peripherals (in this case, selection
of source is done by the Power Manager).
The main oscillator is designed to be used with an external 0.4 to 20MHz crystal and two biasing
capacitors, as shown in
as described in the Power Manager chapter. The oscillator can be used as source for the
generic clocks, as described in
The oscillator is disabled by default after reset. When the oscillator is disabled, the XIN and
XOUT pins can be used as general purpose I/Os. When the oscillator is configured to use an
external clock, the clock must be applied to the XIN pin while the XOUT pin can be used as a
general purpose I/O.
The oscillator can be enabled by writing a one to the OSCEN bit in OSCCTRLn. Operation mode
(external clock or crystal) is chosen by writing to the MODE field in OSCCTRLn. The oscillator is
automatically switched off in certain sleep modes to reduce power consumption, as described in
the Power Manager chapter.
After a hard reset, or when waking up from a sleep mode that disabled the oscillator, the oscilla-
tor may need a certain amount of time to stabilize on the correct frequency. This start-up time
can be set in the OSCCTRLn register.
The SCIF masks the oscillator outputs during the start-up time, to ensure that no unstable clocks
propagate to the digital logic. The OSCnRDY bits in PCLKSR are automatically set and cleared
according to the status of the oscillators. A zero to one transition on these bits can also be con-
figured to generate an interrupt, as described in
Figure
”Generic Clocks” on page
8-1. The oscillator can be used for the main clock in the device,
”Interrupts” on page
84.
88.
AT32UC3C
82