AT32UC3C1512C Atmel Corporation, AT32UC3C1512C Datasheet - Page 495

• Manufacturer Part Number: AT32UC3C1512C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C1512C

• Flash (kbytes): 512 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 81
• Ext Interrupts: 100
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 7
• Twi (i2c): 3
• Uart: 5
• Can: 2
• Lin: 5
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 4
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 68
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 22
• Input Capture Channels: 12
• Pwm Channels: 19
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

24.5.6
32117C–AVR-08/11
Pause Frame Support
64 1s, whenever it sees an incoming frame to force a collision. This provides a way of imple-
menting flow control in half-duplex mode.
The start of an 802.3 pause frame is as follows:
Table 24-3.
The network configuration register contains a receive pause enable bit (13). If a valid pause
frame is received, the pause time register is updated with the frame’s pause time, regardless of
its current contents and regardless of the state of the configuration register bit 13. An interrupt
(12) is triggered when a pause frame is received, assuming it is enabled in the interrupt mask
register. If bit 13 is set in the network configuration register and the value of the pause time reg-
ister is non-zero, no new frame is transmitted until the pause time register has decremented to
zero.
The loading of a new pause time, and hence the pausing of transmission, only occurs when the
MACB is configured for full-duplex operation. If the MACB is configured for half-duplex, there is
no transmission pause, but the pause frame received interrupt is still triggered.
A valid pause frame is defined as having a destination address that matches either the address
stored in specific address register 1 or matches 0x0180C2000001 and has the MAC control
frame type ID of 0x8808 and the pause opcode of 0x0001. Pause frames that have FCS or other
errors are treated as invalid and are discarded. Valid pause frames received increment the
Pause Frame Received statistic register.
The pause time register decrements every 512 bit times (i.e., 128 RX_CLK in nibble mode) once
transmission has stopped. For test purposes, the register decrements every RX_CLK cycle once
transmission has stopped if bit 12 (retry test) is set in the network configuration register. If the
pause enable bit (13) is not set in the network configuration register, then the decrementing
occurs regardless of whether transmission has stopped or not.
An interrupt (13) is asserted whenever the pause time register decrements to zero (assuming it
is enabled in the interrupt mask register). Automatic transmission of pause frames is supported
through the transmit pause frame bits of the network control register and the tx_pause and
tx_pause_zero inputs. If either bit 11 or bit 12 of the network control register is written to with a 1,
or if the input signal tx_pause is toggled, a pause frame is transmitted only if full duplex is
selected in the network configuration register and transmit is enabled in the network control
register.
Pause frame transmission occurs immediately if transmit is inactive or if transmit is active
between the current frame and the next frame due to be transmitted. The transmitted pause
frame is comprised of the items in the following list:
• a destination address of 01-80-C2-00-00-01
• a source address taken from the specific address 1 register
• a type ID of 88-08 (MAC control frame)
• a pause opcode of 00-01
• a pause quantum
Destination Address
0x0180C2000001
Start of an 802.3 Pause Frame
Address
Source
6 bytes
(Mac Control Frame)
0x8808
Type
Opcode
0x0001
Pause
AT32UC3C
Pause Time
2 bytes
495