AT32UC3C1512C Atmel Corporation, AT32UC3C1512C Datasheet - Page 576

• Manufacturer Part Number: AT32UC3C1512C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C1512C

• Flash (kbytes): 512 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 81
• Ext Interrupts: 100
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 7
• Twi (i2c): 3
• Uart: 5
• Can: 2
• Lin: 5
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 4
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 68
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 22
• Input Capture Channels: 12
• Pwm Channels: 19
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

32117C–AVR-08/11
The receiver samples the RXD line. If the line is sampled during one half of a bit time at 0, a start
bit is detected and data, parity and stop bits are successively sampled on the bit rate clock.
If the oversampling is 16, (OVER at 0), a start is detected at the eighth sample at 0. Then, data
bits, parity bit and stop bit are sampled on each 16 sampling clock cycle. If the oversampling is 8
(OVER at 1), a start bit is detected at the fourth sample at 0. Then, data bits, parity bit and stop
bit are sampled on each 8 sampling clock cycle.
The number of data bits, first bit sent and parity mode are selected by the same fields and bits
as the transmitter, i.e. respectively CHRL, MODE9, MSBF and PAR. For the synchronization
mechanism only, the number of stop bits has no effect on the receiver as it considers only one
stop bit, regardless of the field NBSTOP, so that resynchronization between the receiver and the
transmitter can occur. Moreover, as soon as the stop bit is sampled, the receiver starts looking
for a new start bit so that resynchronization can also be accomplished when the transmitter is
operating with one stop bit.
Figure 25-11
operates in asynchronous mode.
Figure 25-11. Asynchronous Start Detection
Figure 25-12. Asynchronous Character Reception
Clock (x16)
Baud Rate
Sampling
Sampling
Sampling
Baud Rate
Example: 8-bit, Parity Enabled
Detection
Clock
RXD
RXD
Start
Clock
RXD
and
1
1
Figure 25-12
2
2
samples
3
3
16
4
4
D0
5
5
samples
16
6
6
illustrate start detection and character reception when USART
D1
7
Detection
7
Rejection
samples
Start
Start
16
8
0
D2
1
1
samples
16
2
2
3
3
D3
samples
4
4
16
5
D4
samples
6
16
7
D5
samples
8
16
9 10 11 12 13 14 15 16
D6
samples
16
D7
samples
AT32UC3C
16
Parity
Bit
samples
16
Stop
Bit
Sampling
D0
576