AT32UC3A464 Atmel Corporation, AT32UC3A464 Datasheet - Page 708

• Manufacturer Part Number: AT32UC3A464
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A464

• Flash (kbytes): 64 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 2
• Uart: 4
• Ssc: 1
• Sd / Emmc: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 128
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

26.8.2.20
Register Name:
Access Type:
Offset:
Reset Value:
• CHBYTECNT: Channel Byte Count
• DESCLDSTA: Descriptor Loaded Status
• EOCHBUFFSTA: End of Channel Buffer Status
• EOTSTA: End of USB Transfer Status
• CHACTIVE: Channel Active
• CHEN: Channel Enabled
32072G–11/2011
31
23
15
7
-
-
This field contains the current number of bytes still to be transferred for this buffer.
This field is decremented at each dma access.
This field is reliable (stable) only if the CHEN bit is zero.
This bit is set when a Descriptor has been loaded from the HSB bus.
This bit is cleared when read by the user.
This bit is set when the Channel Byte Count counts down to zero.
This bit is automatically cleared when read by software.
This bit is set when the completion of the usb data transfer has closed the dma transfer. It is valid only if
UDDMAnCONTROL.BUFFCLOSEINEN is one. Note that for OUT endpoint, if the UECFGn.AUTOSW is set, any received zero-
length-packet will be cancelled by the DMA, and the EOTSTA will be set whatever the UDDMAnCONTROL.CHEN bit is.
This bit is automatically cleared when read by software.
0: the DMA channel is no longer trying to source the packet data.
1: the DMA channel is currently trying to source packet data, i.e. selected as the highest-priority requesting channel. When a
packet transfer cannot be completed due to an EOCHBUFFSTA, this bit stays set during the next channel descriptor load (if
any) and potentially until USB packet transfer completion, if allowed by the new descriptor.
When programming a DMA by descriptor (Load next descriptor now), the CHACTIVE bit is set only once the DMA is running
(the endpoint is free for IN transaction, the endpoint is full for OUT transaction).
This bit is set (after one cycle latency) when the L.CHEN is written to one or when the descriptor is loaded.
This bit is cleared when any transfer is ended either due to an elapsed byte count or a USB device initiated transfer end.
Device DMA Channel n Status Register
DESCLD
STA
30
22
14
6
-
UDDMAnSTATUS, n in [1..7]
Read/Write
0x031C + (n - 1) * 0x10
0x00000000
EOCHBUFF
STA
29
21
13
5
-
EOTSTA
CHBYTECNT[15:8]
28
20
12
CHBYTECNT[7:0]
4
-
27
19
11
3
-
-
26
18
10
2
-
-
CHACTIVE
25
17
9
1
-
CHEN
24
16
8
0
-
708