AT32UC3A464 Atmel Corporation, AT32UC3A464 Datasheet - Page 545

• Manufacturer Part Number: AT32UC3A464
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A464

• Flash (kbytes): 64 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 2
• Uart: 4
• Ssc: 1
• Sd / Emmc: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 128
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

25. Universal Synchronous Asynchronous Receiver Transmitter (USART)
25.1
25.2
32072G–11/2011
Features
Overview
Rev: 4.2.0.6
•
•
•
•
•
•
•
•
•
The Universal Synchronous Asynchronous Receiver Transceiver (USART) provides a full
duplex, universal, synchronous/asynchronous serial link. Data frame format is widely configu-
rable, including basic length, parity, and stop bit settings, maximizing standards support. The
receiver implements parity-, framing-, and overrun error detection, and can handle un-fixed
Configurable baud rate generator
5- to 9-bit full-duplex, synchronous and asynchronous, serial communication
RS485 with line driver control
ISO7816, T=0 and T=1 protocols for Interfacing with smart cards
IrDA modulation and demodulation
SPI Mode
LIN Mode
Test Modes
Supports two Peripheral DMA Controller channels
– 1, 1.5, or 2 stop bits in asynchronous mode, and 1 or 2 in synchronous mode
– Parity generation and error detection
– Framing- and overrun error detection
– MSB- or LSB-first
– Optional break generation and detection
– Receiver frequency over-sampling by 8 or 16 times
– Optional RTS-CTS hardware handshaking
– Optional DTR-DSR-DCD-RI modem signal management
– Receiver Time-out and transmitter Timeguard
– Optional Multidrop mode with address generation and detection
– , NACK handling, and customizable error counter
– Communication at up to 115.2Kbit/s
– Master or slave
– Configurable serial clock phase and polarity
– CLK SPI serial clock frequency up to a quarter of the CLK_USART internal clock frequency
– Compliant with LIN 1.3 and LIN 2.0 specifications
– Master or slave
– Processing of Frames with up to 256 data bytes
– Configurable response data length, optionally defined automatically by the Identifier
– Self synchronization in slave node configuration
– Automatic processing and verification of the “Break Field” and “Sync Field”
– The “Break Field” is detected even if it is partially superimposed with a data byte
– Optional, automatic identifier parity management
– Optional, automatic checksum management
– Supports both “Classic” and “Enhanced” checksum types
– Full LIN error checking and reporting
– Frame Slot Mode: the master allocates slots to scheduled frames automatically.
– Wakeup signal generation
– Automatic echo, remote- and local loopback
– Buffer transfers without processor intervention
545