AT32UC3A364 Atmel Corporation, AT32UC3A364 Datasheet - Page 678

• Manufacturer Part Number: AT32UC3A364
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A364

• Flash (kbytes): 64 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 110
• Ext Interrupts: 110
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 128
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 12
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

26.8.1.10
Register Name:
Access Type:
Offset:
Read Value:
• DRDSTATE
32072G–11/2011
DRDSTATE
10
12
11
31
23
15
0
1
2
3
4
5
6
7
8
9
7
-
-
-
-
This field indicates the state of the USBB.
Finite State Machine Status Register
Description
a_idle state: this is the start state for A-devices (when the ID pin is 0)
a_wait_vrise: In this state, the A-device waits for the voltage on VBus to rise above the A-
device VBus Valid threshold (4.4 V).
a_wait_bcon: In this state, the A-device waits for the B-device to signal a connection.
a_host: In this state, the A-device that operates in Host mode is operational.
a_suspend: The A-device operating as a host is in the suspend mode.
a_peripheral: The A-device operates as a peripheral.
a_wait_vfall: In this state, the A-device waits for the voltage on VBus to drop below the A-
device Session Valid threshold (1.4 V).
a_vbus_err: In this state, the A-device waits for recovery of the over-current condition that
caused it to enter this state.
a_wait_discharge: In this state, the A-device waits for the data usb line to discharge (100
us).
b_idle: this is the start state for B-device (when the ID pin is 1).
b_peripheral: In this state, the B-device acts as the peripheral.
b_wait_begin_hnp: In this state, the B-device is in suspend mode and waits until 3 ms before
initiating the HNP protocol if requested.
b_wait_discharge: In this state, the B-device waits for the data usb line to discharge (100 us)
before becoming Host.
30
22
14
6
-
-
-
-
USBFSM
Read-Only
0x082C
0x00000009
29
21
13
5
-
-
-
-
28
20
12
4
-
-
-
-
27
19
11
3
-
-
-
26
18
10
2
-
-
-
DRDSTATE
25
17
9
1
-
-
-
24
16
8
0
-
-
-
678