DS21Q42T+ Maxim Integrated Products, DS21Q42T+ Datasheet - Page 54

• Manufacturer Part Number: DS21Q42T+
• Description: IC FRAMER ENHANCED T1 4X 128TQFP
• Manufacturer: Maxim Integrated Products

Specifications of DS21Q42T+

• Controller Type: T1 Framer
• Interface: Parallel/Serial
• Voltage - Supply: 2.97 V ~ 3.63 V
• Current - Supply: 75mA
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 128-TQFP, 128-VQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

11.1.1 Simple Idle Code Insertion and Per-Channel Loopback
The first method involves using the Transmit Idle Registers (TIR1/2/3) to determine which of the 24 T1
channels should be overwritten with the code placed in the Transmit Idle Definition Register (TIDR).
This method allows the same 8–bit code to be placed into any of the 24 T1 channels. If this method is
used, then the CCR4.0 control bit must be set to zero.
Each of the bit position in the Transmit Idle Registers (TIR1/TIR2/TIR3) represent a DS0 channel in the
outgoing frame. When these bits are set to a one, the corresponding channel will transmit the Idle Code
contained in the Transmit Idle Definition Register (TIDR). Robbed bit signaling and Bit 7 stuffing will
occur over the programmed Idle Code unless the DS0 channel is made transparent by the Transmit
Transparency Registers.
The Transmit Idle Registers (TIRs) have an alternate function that allow them to define a Per–Channel
LoopBack (PCLB). If the TIRFS control bit (CCR4.0) is set to one, then the TIRs will determine which
channels (if any) from the backplane should be replaced with the data from the receive side or in other
words, off of the T1 line. If this mode is enabled, then transmit and receive clocks and frame syncs must
be synchronized. One method to accomplish this would be to tie RCLK to TCLK and RFSYNC to
TSYNC.
TIR1/TIR2/TIR3: TRANSMIT IDLE REGISTERS (Address=3C to 3E Hex)
[Also used for Per–Channel Loopback]
SYMBOLS POSITIONS NAME AND DESCRIPTION
CH1 – 24
NOTE:
If CCR4.0=1, then a zero in the TIRs implies that channel data is to be sourced from TSER and a one
implies that channel data is to be sourced from the output of the receive side framer (i.e., Per–Channel
Loopback; see Figure 1–1).
TIDR: TRANSMIT IDLE DEFINITION REGISTER (Address=3F Hex)
(MSB)
CH16
CH24
CH8
(MSB)
TIDR7
SYMBOL
TIDR7
TIDR0
CH15
CH23
CH7
TIDR6
TIR1.0 - 3.7
CH14
CH22
CH6
POSITION
TIDR.7
TIDR.0
TIDR5
CH13
CH21
CH5
TIDR4
Transmit Idle Code Insertion Control Bits.
0 = do not insert the Idle Code in the TIDR into this channel
1 = insert the Idle Code in the TIDR into this channel
NAME AND DESCRIPTION
LSB of the Idle Code (this bit is transmitted last)
MSB of the Idle Code (this bit is transmitted first)
CH12
CH20
CH4
54 of 116
CH11
CH19
CH3
TIDR3
CH10
CH18
CH2
TIDR2
(LSB)
CH17
CH1
CH9
TIDR1
TIR2 (3D)
TIR1 (3C)
TIR3 (3E)
TIDR0
(LSB)