ADE5569ASTZF62 Analog Devices Inc, ADE5569ASTZF62 Datasheet - Page 105

• Manufacturer Part Number: ADE5569ASTZF62
• Description: IC METER/8052/RTC/LCD DRV 64LQFP
• Manufacturer: Analog Devices Inc

Specifications of ADE5569ASTZF62

• Applications: Energy Measurement
• Core Processor: 8052
• Program Memory Type: FLASH (62kB)
• Controller Series: ADE55xx
• Ram Size: 2.25K x 8
• Interface: I²C, SPI, UART
• Number Of I /o: 20
• Voltage - Supply: 3.135 V ~ 3.465 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 64-LQFP
• Ic Function: Single Phase Energy Measurement IC
• Supply Voltage Range: 3.13V To 3.46V, 2.4V To 3.7V
• Operating Temperature Range: -40°C To +85°C
• Digital Ic Case Style: LQFP
• No. Of Pins: 64
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Charge Pump
Voltage generation through the charge pump requires external
capacitors to store charge. The external connections to LCDVA,
LCDVB, and LCDVC, as well as to LCDVP1 and LCDVP2, are
shown in Figure 90.
External Resistor Ladder
Set the EXTRES bit (Bit 6) in the LCD Configuration X SFR
(LCDCONX, Address 0x9C) to enable the external resistor ladder
option. When EXTRES = 1, the LCD waveform voltages are sup-
plied by the external resistor ladder. Because the LCD voltages
are not generated on chip, the LCD bias compensation that is
implemented to maintain contrast over temperature and supply
is not possible.
The external circuitry needed for the resistor ladder option is
shown in Figure 91. The resistors required should be in the range
of 10 kΩ to 100 kΩ and should be based on the current required
by the LCD being used.
LCD FUNCTION IN PSM2 MODE
LCDPSM2 (Bit 4) and LCDEN (Bit 7) in the LCD configuration
SFR (LCDCON, Address 0x95) control the LCD functionality
in the PSM2 operating mode (see Table 103).
Note that the internal voltage reference must be enabled by set-
ting REF_BAT_EN (Bit 3) in the peripheral configuration SFR
(PERIPH, Address 0xF4) to allow LCD operation in PSM2
mode (see Table 20).
Table 103. Bits Controlling LCD Functionality in PSM2 Mode
LCDPSM2
0
0
1
In addition, note that the LCD configuration and data memory
are retained when the display is turned off.
Example LCD Setup
An example of how to set up the LCD peripheral for a specific
LCD is described in this section with the following parameters:
LCD WAVEFORM
CHARGE PUMP
Figure 91. External Circuitry for External Resistor Ladder Option
CIRCUITRY
AND
Figure 90. External Circuitry for Charge Pump Option
LCD WAVEFORM
LCDEN
0
1
X
CIRCUITRY
LCDVP1
LCDVP2
LCDVC
LCDVB
LCDVA
Result
The display is off in PSM2.
The display is on in PSM2.
The display is off in PSM2.
100nF
LCDVP1
LCDVP2
LCDVC
LCDVB
LCDVA
470nF
470nF
470nF
Rev. C | Page 105 of 156
•
•
•
A 96-segment LCD with 4× multiplexing requires 96/4 = 24
segment lines. Sixteen pins, FP0 to FP15, are automatically
dedicated for use as LCD segments. Eight more pins must be
chosen for the LCD function. Because the LCD has 4× multi-
plexing, all four common lines are used. As a result, COM2/FP28
and COM3/FP27 cannot be used as segment lines. Based on the
alternate functions of the pins used for FP16 through FP25, FP16 to
FP23 are chosen for the eight remaining segment lines. These
pins are enabled for LCD functionality in the LCD segment
enable SFR (LCDSEGE, Address 0x97) and the LCD Segment
Enable 2 SFR (LCDSEGE2, Address 0xED).
To determine the contrast setting for this 5 V LCD, see Table 93
for the BIASLVL bit settings in the LCD Configuration X SFR
(LCDCONX, Address 0x9C) that correspond to a V
1/3 bias mode. The maximum bias level setting for this LCD is
BIASLVL = 101110.
The LCD is set up with the following 8052 code:
; set up LCD pins to have LCD functionality
MOV
MOV
; set up LCDCON for f
and 4x multiplexing
MOV
; set up LCDCONX for charge pump and
BIASLVL[110111]
MOV
ASLVL2+BIASLVL1+BIASLVL0
; set up refresh rate for 64Hz with f
2048 Hz
MOV
; set up LCD data registers with data to be
displayed using
; LCDPTR and LCDDAT registers
; turn all segments on FP27 ON
ORL
refresh
MOV
MOV
ANL
refresh
ORL
To set up the same 3.3 V LCD for use with an external resistor
ladder,
; setup LCDCONX for external resistor ladder
MOV
ADE5166/ADE5169/ADE5566/ADE5569
Type of LCD: 5 V, 4× multiplexed with 1/3 bias, 96 segments
Voltage generation: internal charge pump
Refresh rate: 64 Hz
LCDSEGE,#FP20EN+FP21EN+FP22EN+FP23EN
LCDSEGE2,#FP16EN+FP17EN+FP18EN+FP19EN
LCDCON,#BIAS+LMUX1+LMUX0
LCDCONX,#BIASLVL5+BIASLVL4+BIASLVL3+BI
LCDCLK,#FD3+FD2+FD1+FD0
LCDCONY,#01h ; start data memory
LCDDAT,#F0H
LCDCONY,#0FEh ; end of data memory
LCDCON,#LCDEN ; enable LCD
LCDCONX,#EXTRES
LCDPTR, #80h OR 0DH
LCDCLK
= 2048Hz, 1/3 bias
C
LCDCLK
of 5 V in
=