PIC18LF27J13T-I/SO Microchip Technology, PIC18LF27J13T-I/SO Datasheet - Page 418

• Manufacturer Part Number: PIC18LF27J13T-I/SO
• Description: 28-pin, GP, 128KB Flash, 4KB RAM, 12 MIPS, 12-bit ADC 28 SOIC .300in T/R
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18LF27J13T-I/SO

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 128KB (64K x 16)
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 2.75 V
• Data Converters: A/D 10x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIC18F47J13 FAMILY
REGISTER 27-2:
REGISTER 27-3:
DS39974A-page 418
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7-4
bit 3
bit 2
bit 1-0
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4-3
bit 2-0
R/WO-1
IESO
U-1
—
IESO: Two-Speed Start-up (Internal/External Oscillator Switchover) Control bit
1 = Two-Speed Start-up is enabled
0 = Two-Speed Start-up is disabled
FCMEN: Fail-Safe Clock Monitor Enable bit
1 = Fail-Safe Clock Monitor is enabled
0 = Fail-Safe Clock Monitor is disabled
CLKOEC: CLKO Enable Configuration bit
(Applicable only when the FOSC<2:1> bits are configured for EC or ECPLL mode.)
1 = CLKO output signal is active on the RA6 pin
0 = CLKO output is disabled
SOSCSEL<1:0>: T1OSC/SOSC Power Selection Configuration bits
11 = High-power T1OSC/SOSC circuit is selected
10 = Digital (SCLKI) mode is enabled
01 = Low-power T1OSC/SOSC circuit is selected
00 = Reserved
FOSC<2:0>: Oscillator Selection bits
111 = ECPLL oscillator with PLL software controlled; CLKO on RA6
110 = EC oscillator with CLKO on RA6
101 = HSPLL oscillator with PLL software controlled
100 = HS oscillator
011 = INTOSCPLLO, internal oscillator with PLL software controlled; CLKO on RA6; port function on RA7
010 = INTOSCPLL, internal oscillator with PLL software controlled; port function on RA6 and RA7
001 = INTOSCO internal oscillator block (INTRC/INTOSC) with CLKO on RA6; port function on RA7
000 = INTOSC internal oscillator block (INTRC/INTOSC); port function on RA6 and RA7
Unimplemented: Program the corresponding Flash Configuration bit to ‘1’
Unimplemented: Maintain as ‘0’
CP0: Code Protection bit
1 = Program memory is not code-protected
0 = Program memory is code-protected
Unimplemented: Maintain as ‘1’
R/WO-1
FCMEN
U-1
—
CONFIG1H: CONFIGURATION REGISTER 1 HIGH (BYTE ADDRESS 300001h)
CONFIG2L: CONFIGURATION REGISTER 2 LOW (BYTE ADDRESS 300002h)
WO = Write-Once bit
‘1’ = Bit is set
WO = Write-Once bit
‘1’ = Bit is set
CLKOEC
R/WO-1
U-1
—
SOSCSEL1 SOSCSEL0
R/WO-1
U-1
Preliminary
—
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R/WO-1
U-0
—
R/WO-1
FOSC2
R/WO-1
CP0
 2010 Microchip Technology Inc.
x = Bit is unknown
x = Bit is unknown
R/WO-1
FOSC1
U-1
—
R/WO-1
FOSC0
U-1
—
bit 0
bit 0