STM32W108B-SK STMicroelectronics, STM32W108B-SK Datasheet - Page 108

• Manufacturer Part Number: STM32W108B-SK
• Description: STARTER KIT FOR STM32W108
• Manufacturer: STMicroelectronics
• Series: STM32r
• Type: MCUr

Specifications of STM32W108B-SK

• Featured Product: STM32 Cortex-M3 Companion Products
• Contents: Board
• Silicon Manufacturer: ST Micro
• Core Architecture: ARM
• Core Sub-architecture: Cortex - M3
• Silicon Core Number: STM32
• Silicon Family Name: STM32W108xx
• Kit Contents: Board
• Features: IEEE
• Mfg Application Notes: STM32W108 Adjacent Channel Rejection Measurements
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: *
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

General-purpose timers
10.1.1
108/209
The GPIOs that can be used by Timer 1 are fixed, but the GPIOs that can be used as Timer
2 channels can be mapped to either of two pins, as shown in
Register (TIM2_OR) has four single bit fields (TIM_REMAPCy) that control whether a Timer
2 channel is mapped to its default GPIO in port PA, or remapped to a GPIO in PB.
Table 23
Table 23.
The TIMxCLK and TIMxMSK inputs can be used only in the external clock modes: refer to
the External Clock Source Mode 1 and External Clock Source Mode 2 sections for details
concerning their use.
Time-base unit
The main block of the general purpose timer is a 16-bit counter with its related auto-reload
register. The counter can count up, down, or alternate up and down. The counter clock can
be divided by a prescaler.
The counter, the auto-reload register, and the prescaler register can be written to or read by
software. This is true even when the counter is running.
The time-base unit includes:
●
●
●
Some timer registers cannot be directly accessed by software, which instead reads and
writes a "buffer register". The internal registers actually used for timer operations are called
"shadow registers".
The auto-reload register is buffered. Writing to or reading from the auto-reload register
accesses the buffer register. The contents of the buffer register are transferred into the
shadow register permanently or at each update event (UEV), depending on the auto-reload
buffer enable bit (TIM_ARBE) in the TIMx_CR1 register. The update event is generated
when both the counter reaches the overflow (or underflow when down-counting) and when
the TIM_UDIS bit equals 0 in the TIMx_CR1 register. It can also be generated by software.
Update event generation is described in detail for each configuration.
The counter is clocked by the prescaler output CK_CNT, which is enabled only when the
counter enable bit (TIM_CEN) in the TIMx_CR1 register is set. Refer also to the slave mode
controller description in the Timers and External Trigger Synchronization section to get more
details on counter enabling.
Note that the actual counter enable signal CNT_EN is set one clock cycle after TIM_CEN.
Timer 1
Timer 2
(TIM_REMAPCy = 0)
Timer 2
(TIM_REMAPCy = 1)
Signal (direction)
Counter register (TIMx_CNT)
Prescaler register (TIMx_PSC)
Auto-reload register (TIMx_ARR)
specifies the pins that may be assigned to Timer 1 and Timer 2 functions.
Timer GPIO use
(in or out)
TIMxC1
PB6
PB1
PA0
Doc ID 16252 Rev 8
(in or out)
TIMxC2
PB7
PB2
PA3
(in or out)
TIMxC3
PB3
PA6
PA1
STM32W108CB, STM32W108HB
(in or out)
TIMxC4
PB4
PA7
PA2
Table
23. The Timer 2 Option
TIMxCLK
PB0
PB5
PB5
(in)
TIMxMSK
PB5
PB0
PB0
(in)