SAF-XC164CS-32F40F BB-A Infineon Technologies, SAF-XC164CS-32F40F BB-A Datasheet - Page 16

• Manufacturer Part Number: SAF-XC164CS-32F40F BB-A
• Description: IC MCU 16BIT 256KB FLSH 100TQFP
• Manufacturer: Infineon Technologies
• Series: XC16xr

Specifications of SAF-XC164CS-32F40F BB-A

• Core Processor: C166SV2
• Core Size: 16-Bit
• Speed: 40MHz
• Connectivity: CAN, EBI/EMI, SPI, UART/USART
• Peripherals: PWM, WDT
• Number Of I /o: 79
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 12K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 2.7 V
• Data Converters: A/D 14x8/10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LFQFP
• Data Bus Width: 16 bit
• Data Ram Size: 12 KB
• Interface Type: 2xASC, 2xSSC
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 79
• Number Of Timers: 11
• Operating Supply Voltage: 5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 14 Channel
• Packages: PG-TQFP-100
• Max Clock Frequency: 40.0 MHz
• Sram (incl. Cache): 12.0 KByte
• Can Nodes: 2
• A / D Input Lines (incl. Fadc): 14
• Program Memory: 256.0 KByte
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Table 2
Sym-
bol
PORT0
P0L.0 -
P0L.7
P0H.0 -
P0H.3
P0H.4 -
P0H.7
PORT1
P1L.0
P1L.1
P1L.2
P1L.3
P1L.4
P1L.5
P1L.6
P1L.7
P1H
Data Sheet
Pin
Num.
67 - 74
4 - 7
75 - 78
79
80
81
82
83
84
85
86
…
Pin Definitions and Functions (cont’d)
Input
Outp.
IO
IO
I/O
O
I/O
O
I/O
O
O
I
I/O
Function
PORT0 consists of the two 8-bit bidirectional I/O ports P0L
and P0H. Each pin can be programmed for input (output
driver in high-impedance state) or output.
In case of an external bus configuration, PORT0 serves as
the address (A) and address/data (AD) bus in multiplexed
bus modes and as the data (D) bus in demultiplexed bus
modes.
Demultiplexed bus modes:
8-bit data bus: P0H = I/O, P0L = D7 - D0
16-bit data bus: P0H = D15 - D8, P0L = D7 - D0
Multiplexed bus modes:
8-bit data bus: P0H = A15 - A8, P0L = AD7 - AD0
16-bit data bus: P0H = AD15 - AD8, P0L = AD7 - AD0
Note: At the end of an external reset (EA = 0) PORT0 also
PORT1 consists of the two 8-bit bidirectional I/O ports P1L
and P1H. Each pin can be programmed for input (output
driver in high-impedance state) or output.
PORT1 is used as the 16-bit address bus (A) in
demultiplexed bus modes (also after switching from a
demultiplexed to a multiplexed bus mode).
The following PORT1 pins also serve for alt. functions:
CC60
COUT60
CC61
COUT61
CC62
COUT62
COUT63
CTRAP
CTRAP is an input pin with an internal pull-up resistor. A low
level on this pin switches the CAPCOM6 compare outputs to
the logic level defined by software (if enabled).
CC22IO
…continued…
may input configuration values
CAPCOM6: Input / Output of Channel 0
CAPCOM6: Output of Channel 0
CAPCOM6: Input / Output of Channel 1
CAPCOM6: Output of Channel 1
CAPCOM6: Input / Output of Channel 2
CAPCOM6: Output of Channel 2
Output of 10-bit Compare Channel
CAPCOM6: Trap Input
CAPCOM2: CC22 Capture Inp./Compare Outp.
14
General Device Information
Derivatives
V1.1, 2006-08
XC164-32