AT91M55800A-33CJ Atmel, AT91M55800A-33CJ Datasheet - Page 139

• Manufacturer Part Number: AT91M55800A-33CJ
• Description: IC ARM MCU 16BIT 176BGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91M55800A-33CJ

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 33MHz
• Connectivity: EBI/EMI, SPI, UART/USART
• Peripherals: POR, WDT
• Number Of I /o: 58
• Program Memory Type: ROMless
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 2x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 176-LFBGA
• Processor Series: AT91Mx
• Core: ARM7TDMI
• Data Bus Width: 32 bit
• Data Ram Size: 8 KB
• Interface Type: EBI, SPI, USART
• Maximum Clock Frequency: 33 MHz
• Number Of Programmable I/os: 58
• Number Of Timers: 10 bit
• Operating Supply Voltage: 3 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91EB55
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• On-chip Dac: 8 bit, 2 Channel
• Cpu Family: AT91
• Device Core: ARM7TDMI
• Device Core Size: 32b
• Frequency (max): 33MHz
• Program Memory Size: Not Required
• Total Internal Ram Size: 8KB
• # I/os (max): 58
• Number Of Timers - General Purpose: 6
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 176
• Package Type: BGA
• For Use With: AT91EB55 - KIT EVAL FOR ARM AT91M55800A
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

18.4
18.4.1
18.5
1745F–ATARM–06-Sep-07
Transmitter
Multi-drop Mode
Time-guard
The transmitter has the same behavior in both synchronous and asynchronous operating
modes. Start bit, data bits, parity bit and stop bits are serially shifted, lowest significant bit first,
on the falling edge of the serial clock. See example in
The number of data bits is selected in the CHRL field in US_MR.
The parity bit is set according to the PAR field in US_MR.
The number of stop bits is selected in the NBSTOP field in US_MR.
When a character is written to US_THR (Transmit Holding), it is transferred to the Shift Register
as soon as it is empty. When the transfer occurs, the TXRDY bit in US_CSR is set until a new
character is written to US_THR. If Transmit Shift Register and US_THR are both empty, the
TXEMPTY bit in US_CSR is set.
The Time-guard function allows the transmitter to insert an idle state on the TXD line between
two characters. The duration of the idle state is programmed in US_TTGR (Transmitter Time-
guard). When this register is set to zero, no time-guard is generated. Otherwise, the transmitter
holds a high level on TXD after each transmitted byte during the number of bit periods pro-
grammed in US_TTGR.
When the field PAR in US_MR equals 11X (binary value), the USART is configured to run in
multi-drop mode. In this case, the parity error bit PARE in US_CSR is set when data is detected
with a parity bit set to identify an address byte. PARE is cleared with the Reset Status Bits Com-
mand (RSTSTA) in US_CR. If the parity bit is detected low, identifying a data byte, PARE is not
set.
The transmitter sends an address byte (parity bit set) when a Send Address Command
(SENDA) is written to US_CR. In this case, the next byte written to US_THR will be transmitted
as an address. After this any byte transmitted will have the parity bit cleared.
Figure 18-6. Synchronous and Asynchronous Modes: Character Transmission
between two characters
Baud Rate
Example: 8-bit, parity enabled 1 stop
Idle state duration
Clock
TXD
Start
Bit
D0
=
Time-guard
D1
value
D2
•
D3
period
Bit
D4
Figure
D5
18-6.
D6
AT91M5880A
D7
Parity
Bit
Stop
Bit
139