AT91SAM9260B-CU-999 Atmel, AT91SAM9260B-CU-999 Datasheet - Page 760

• Manufacturer Part Number: AT91SAM9260B-CU-999
• Description: IC MCU ARM9 217LFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9260B-CU-999

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 180MHz
• Connectivity: EBI/EMI, Ethernet, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: POR, WDT
• Number Of I /o: 96
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: ROM
• Ram Size: 24K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 217-LFBGA
• Processor Series: AT91SAMx
• Core: ARM926EJ-S
• Data Bus Width: 32 bit
• Data Ram Size: 8 KB
• Interface Type: 2-Wire, EBI, I2S, SPI, USART
• Maximum Clock Frequency: 180 MHz
• Number Of Programmable I/os: 96
• Number Of Timers: 6
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM9260-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 4 Channel
• For Use With: AT91SAM9260-EK - KIT EVAL FOR AT91SAM9260AT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

43.2.6.3
43.2.6.4
43.2.6.5
43.2.7
43.2.7.1
760
AT91SAM9260
Reset Controller (RSTC)
Data Timeout Error Flag
Data Write Operation and Number of Bytes
Flag Reset is Not Correct in Half Duplex Mode
RSTC: Reset during SDRAM Accesses
As the data Timeout error flag checking the Naac timing cannot rise, the MCI can be stalled wait-
ing indefinitely the Data start bit.
A STOP command must be sent with a software timeout.
The Data Write operation with a number of bytes less than 12 is impossible.
The PDC counters must always be equal to 12 bytes for data transfers lower than 12 bytes. The
BLKLEN or BCNT field are used to specify the real count number.
In half duplex mode, the reset of the flags ENDRX, RXBUFF, ENDTX and TXBUFE can be
incorrect.
These flags are reset correctly after a PDC channel enable.
Enable the interrupts related to ENDRX, ENDTX, RXBUFF and TXBUFE only after enabling the
PDC channel by writing PDC_TXTEN or PDC_RXTEN.
When a User Reset occurs during SDRAM read access, the SDRAM clock is turned off while
data is ready to be read on the data bus. The SDRAM maintains the data until the clock restarts.
If the User Reset is programmed to assert a general reset, the data maintained by the SDRAM
leads to a data bus conflict and adversely affects the boot memories connected on the EBI:
In the interrupt routine, power down the SDRAM properly and perform Peripheral and Processor
Reset with software in assembler.
Example with libV3.
• NAND Flash boot functionality, if the system boots out of internal ROM.
• NOR Flash boot, if the system boots on an external memory connected on the EBI CS0.
1. Avoid User Reset to generate a system reset.
2. Trap the User Reset with an interrupt.
• The main code:
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
//user reset interrupt setting
// Configure AIC controller to handle SSC interrupts
AT91F_AIC_ConfigureIt (
AT91C_BASE_AIC,
AT91C_ID_SYS,
AT91C_AIC_PRIOR_HIGHEST,
AT91C_AIC_SRCTYPE_INT_EDGE_TRIGGERED, // Level sensitive
sysc_handler );
// System peripheral ID
// AIC base address
// Max priority
6221I–ATARM–17-Jul-09