M30833FJFP#U3 Renesas Electronics America, M30833FJFP#U3 Datasheet - Page 115

• Manufacturer Part Number: M30833FJFP#U3
• Description: IC M32C/83 MCU FLASH 100QFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M32C/80r

Specifications of M30833FJFP#U3

• Core Processor: M32C/80
• Core Size: 16/32-Bit
• Speed: 32MHz
• Connectivity: CAN, I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, WDT
• Number Of I /o: 85
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 31K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 26x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-QFP
• For Use With: R0K330879S001BE - KIT DEV RSK M32C/87R0K330879S000BE - KIT DEV RSK M32C/87
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

R
R
M
10.3 Hardware Interrupts
e
E
3
. v
J
2
0
10.2.4 BRK2 Interrupt
10.2.5 INT Instruction Interrupt
Special interrupts and peripheral function interrupts are available as hardware interrupts.
10.3.1 Special Interrupts
1
9
C
3 .
B
The BRK2 interrupt occurs when the BRK2 instruction is executed.
Do not use this interrupt. For development support tools only.
The INT instruction interrupt occurs when the INT instruction is executed. The INT instruction can select
software interrupt numbers 0 to 63. Software interrupt numbers 7 to 54, and 57 are assigned to the vector
table used for the peripheral function interrupt. Therefore, the microcomputer executes the same service
routine when the INT instruction is executed as when a peripheral function interrupt occurs.
When the INT instruction is executed, the FLG register and PC are saved to the stack. PC also stores the
relocatable vector of the specified software interrupt number. Where the stack is saved varies, depend-
ing on the software interrupt number. ISP is selected as the stack for the software interrupt numbers 0 to
31 (the U flag is set to "0"). SP, which is set before the INT instruction is executed, is selected as the stack
for the software interrupt numbers 32 to 63 (the U flag is not changed).
With the peripheral function interrupt, the FLG register is saved and the U flag is set to "0" (ISP select)
when an interrupt request is acknowledged. With software interrupt numbers 32 to 54 and 57, the SP to
be used varies, depending on whether the interrupt is generated by the peripheral function interrupt
request or by the INT instruction.
Special interrupts are non-maskable interrupts.
8 /
0
1
10.3.1.1 NMI Interrupt
10.3.1.2 Watchdog Timer Interrupt
10.3.1.3 Oscillation Stop Detection Interrupt
10.3.1.4 Single-Step Interrupt
10.3.1.5 Address Match Interrupt
3
0
The NMI interrupt occurs when a signal applied to the NMI pin changes from an "H" signal to an "L"
signal. Refer to 10.8 NMI Interrupt for details.
The watchdog timer interrupt occurs when the count source of the watchdog timer underflows. Refer
to 11. Watchdog Timer for details.
The oscillation stop detection interrupt occurs when the microcomputer detects a main clock oscilla-
tion stop. Refer to 8. Clock Generating Circuit for details.
Do not use the single-step interrupt. For development support tool only.
The address match interrupt occurs immediately before executing an instruction that is stored into an
address indicated by the RMADi register (i=0 to 3) when the AIERi bit in the AIER register is set to "1"
(address match interrupt enabled). Set the starting address of the instruction in the RMADi register.
The address match interrupt does not occur when a table data or addresses of the instruction other
than the starting address, if the instruction has multiple addresses, is set. Refer to 10.10 Address
Match Interrupt for details.
3
J
G
4
a
0 -
n
o r
3 .
1
u
______
, 1
3
p
1
2
(
______
M
0
0
3
6
2
C
8 /
Page 90
, 3
M
3
______
2
C
f o
8 /
4
3
8
) T
8
______
10. Interrupts