R5F212A8SNFP#U0 Renesas Electronics America, R5F212A8SNFP#U0 Datasheet - Page 73

• Manufacturer Part Number: R5F212A8SNFP#U0
• Description: IC R8C/2A MCU FLASH 64LQFP
• Manufacturer: Renesas Electronics America
• Series: R8C/2x/2Ar

Specifications of R5F212A8SNFP#U0

• Core Processor: R8C
• Core Size: 16/32-Bit
• Speed: 20MHz
• Connectivity: I²C, LIN, SIO, SSU, UART/USART
• Peripherals: POR, PWM, Voltage Detect, WDT
• Number Of I /o: 55
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 3K x 8
• Voltage - Supply (vcc/vdd): 2.2 V ~ 5.5 V
• Data Converters: A/D 12x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 64-LQFP
• For Use With: R0K5212D8S001BE - KIT STARTER FOR R8C/2DR0K5212D8S000BE - KIT DEV FOR R8C/2D
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

R8C/2A Group, R8C/2B Group
Rev.2.00
REJ09B0324-0200
6.3
Table 6.3
NOTES:
Table 6.3 lists the Procedure for Setting Bits Associated with Voltage Monitor 1 Interrupt and Reset. Figure 6.10
shows an Example of Voltage Monitor 1 Interrupt and Voltage Monitor 1 Reset Operation. To use the voltage
monitor 1 interrupt or voltage monitor 1 reset to exit stop mode, set the VW1C1 bit in the VW1C register to 1
(digital filter disabled).
1. Set the VW1C7 bit to 1 (when VCC reaches Vdet1 or below) for the voltage monitor 1 reset.
2. When the VW1C0 bit is set to 0, steps 3, 4, and 5 can be executed simultaneously (with 1
Step
4
5
1
2
3
6
7
8
9
instruction).
(2)
(2)
Voltage Monitor 1 Interrupt and Voltage Monitor 1 Reset
Nov 26, 2007
Set the VCA26 bit in the VCA2 register to 1 (voltage detection 1 circuit enabled)
Wait for td(E-A)
Select the sampling clock of the digital filter
by the VW1F0 to VW1F1 bits in the VW1C
register
Set the VW1C1 bit in the VW1C register to 0
(digital filter enabled)
Set the VW1C6 bit in
the VW1C register to
0 (voltage monitor 1
interrupt mode)
Set the VW1C2 bit in the VW1C register to 0 (passing of Vdet1 is not detected)
Set the CM14 bit in the CM1 register to 0
(low-speed on-chip oscillator on)
Wait for 4 cycles of the sampling clock of the
digital filter
Set the VW1C0 bit in the VW1C register to 1 (voltage monitor 1 interrupt/reset enabled)
Procedure for Setting Bits Associated with Voltage Monitor 1 Interrupt and Reset
Voltage Monitor 1
Interrupt
Page 51 of 580
When Using Digital Filter
Set the VW1C6 bit in
the VW1C register to
1 (voltage monitor 1
reset mode)
Voltage Monitor 1
Reset
Select the timing of the interrupt and reset
request by the VW1C7 bit in the VW1C
register
Set the VW1C1 bit in the VW1C register to 1
(digital filter disabled)
Set the VW1C6 bit in
the VW1C register to
0 (voltage monitor 1
interrupt mode)
-
− (No wait time required)
Voltage Monitor 1
Interrupt
(1)
When Not Using Digital Filter
6. Voltage Detection Circuit
Set the VW1C6 bit in
the VW1C register to
1 (voltage monitor 1
reset mode)
Voltage Monitor 1
Reset