PIC18F45J50-I/PT Microchip Technology, PIC18F45J50-I/PT Datasheet - Page 29

• Manufacturer Part Number: PIC18F45J50-I/PT
• Description: IC PIC MCU FLASH 32K 2V 44-TQFP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F45J50-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 32KB (16K x 16)
• Package / Case: 44-TQFP, 44-VQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 34
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• Interface Type: EUSART, I2C, SPI
• Maximum Clock Frequency: 48 MHz
• Number Of Timers: 5
• Operating Supply Voltage: 2.25 V to 2.75 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136, DM183032, MA180024, DM183022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 13 Channel
• Controller Family/series: PIC18
• No. Of I/o's: 22
• Ram Memory Size: 3776Byte
• Cpu Speed: 48MHz
• No. Of Timers: 5
• Embedded Interface Type: EUSART, I2C, SPI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

2.0
2.1
Devices in the PIC18F46J50 Family incorporate a
different oscillator and microcontroller clock system
than general purpose PIC18F devices. Besides the
USB module, with its unique requirements for a stable
clock source, make it necessary to provide a separate
clock source that is compliant with both USB low-speed
and full-speed specifications.
The PIC18F46J50 Family has additional prescalers
and postscalers, which have been added to accommo-
date a wide range of oscillator frequencies. Figure 2-1
provides an overview of the oscillator structure.
Other oscillator features used in PIC18 enhanced
microcontrollers, such as the internal oscillator block
and clock switching, remain the same. They are
discussed later in this chapter.
2.1.1
The operation of the oscillator in PIC18F46J50 Family
devices is controlled through three Configuration regis-
ters and two control registers. Configuration registers,
CONFIG1L, CONFIG1H and CONFIG2L, select the
oscillator mode, PLL prescaler and CPU divider
options. As Configuration bits, these are set when the
device is programmed and left in that configuration until
the device is reprogrammed.
The OSCCON register (Register 2-2) selects the Active
Clock mode; it is primarily used in controlling clock
switching in power-managed modes. Its use is
discussed in Section 2.5.1 “Oscillator Control
Register”.
The OSCTUNE register (Register 2-1) is used to trim the
INTOSC
low-frequency clock source that drives several special
features. The OSCTUNE register is also used to activate
or disable the Phase Locked Loop (PLL). Its use is
described in Section 2.2.5.1 “OSCTUNE Register”.
2.2
PIC18F46J50 Family devices can be operated in eight
distinct oscillator modes. Users can program the
FOSC<2:0> Configuration bits to select one of the
modes listed in Table 2-1. For oscillator modes which
produce a clock output (CLKO) on pin RA6, the output
frequency will be one fourth of the peripheral clock
frequency. The clock output stops when in Sleep mode,
but will continue during Idle mode (see Figure 2-1).
© 2009 Microchip Technology Inc.
OSCILLATOR
CONFIGURATIONS
Overview
Oscillator Types
frequency
OSCILLATOR CONTROL
source,
and
select
the
PIC18F46J50 FAMILY
TABLE 2-1:
INTOSCPLLO Internal Oscillator mode, PLL can be
INTOSCPLL Internal Oscillator mode, PLL can be
INTOSCO
INTOSC
ECPLL
HSPLL
Mode
EC
HS
External Clock Input mode, the PLL can
be enabled or disabled in software,
CLKO on RA6, apply external clock
signal to RA7.
always disabled, CLKO on RA6, apply
external clock signal to RA7.
PLL can be enabled or disabled in
software, crystal/resonator connected
between RA6 and RA7.
PLL always disabled, crystal/resonator
connected between RA6 and RA7.
enabled or disabled in software, CLKO
on RA6, port function on RA7, the
internal oscillator block is used to derive
both the primary clock source and the
postscaled internal clock.
enabled or disabled in software, port
function on RA6 and RA7, the internal
oscillator block is used to derive both the
primary clock source and the postscaled
internal clock.
Internal Oscillator mode, PLL is always
disabled, CLKO on RA6, port function on
RA7, the output of the INTOSC
postscaler serves as both the postscaled
internal clock and the primary clock
source.
disabled, port function on RA6 and RA7,
the output of the INTOSC postscaler
serves as both the postscaled internal
clock and the primary clock source.
External Clock Input mode, the PLL is
High-Speed Crystal/Resonator mode,
High-Speed Crystal/Resonator mode,
Internal Oscillator mode, PLL is always
OSCILLATOR MODES
Description
DS39931C-page 29