PIC18F45J50-I/PT Microchip Technology, PIC18F45J50-I/PT Datasheet - Page 193

• Manufacturer Part Number: PIC18F45J50-I/PT
• Description: IC PIC MCU FLASH 32K 2V 44-TQFP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F45J50-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 32KB (16K x 16)
• Package / Case: 44-TQFP, 44-VQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 34
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• Interface Type: EUSART, I2C, SPI
• Maximum Clock Frequency: 48 MHz
• Number Of Timers: 5
• Operating Supply Voltage: 2.25 V to 2.75 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136, DM183032, MA180024, DM183022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 13 Channel
• Controller Family/series: PIC18
• No. Of I/o's: 22
• Ram Memory Size: 3776Byte
• Cpu Speed: 48MHz
• No. Of Timers: 5
• Embedded Interface Type: EUSART, I2C, SPI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

12.0
The Timer1 timer/counter module incorporates these
features:
• Software selectable operation as a 16-bit timer or
• Readable and writable 8-bit registers (TMR1H
• Selectable clock source (internal or external) with
• Interrupt-on-overflow
• Reset on ECCP Special Event Trigger
• Device clock status flag (T1RUN)
• Timer with gated control
REGISTER 12-1:
© 2009 Microchip Technology Inc.
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7-6
bit 5-4
bit 3
bit 2
bit 1
bit 0
Note 1:
counter
and TMR1L)
device clock or Timer1 oscillator internal options
TMR1CS1
R/W-0
2:
TIMER1 MODULE
The F
The Timer1 oscillator crystal driver is powered whenever T1OSCEN (T1CON) or T3OSCEN (T3CON) = 1.
The circuit is enabled by the logical OR of these two bits. When disabled, the inverter and feedback resistor
are disabled to eliminate power drain. The TMR1ON and TMR3ON bits do not have to be enabled to power
up the crystal driver.
TMR1CS<1:0>: Timer1 Clock Source Select bits
10 = Timer1 clock source is T1OSC or T1CKI pin
01 = Timer1 clock source is system clock (F
00 = Timer1 clock source is instruction clock (F
T1CKPS<1:0>: Timer1 Input Clock Prescale Select bits
11 = 1:8 Prescale value
10 = 1:4 Prescale value
01 = 1:2 Prescale value
00 = 1:1 Prescale value
T1OSCEN: Timer1 Oscillator Source Select bit
When TMR1CS<1:0> = 10:
1 = Power up the Timer1 crystal driver and supply the Timer1 clock from the crystal output
0 = Timer1 crystal driver off
When TMR1CS<1:0> = 0x:
1 = Power up the Timer1 crystal driver
0 = Timer1 crystal driver off
T1SYNC: Timer1 External Clock Input Synchronization Select bit
TMR1CS<1:0> = 10:
1 = Do not synchronize external clock input
0 = Synchronize external clock input
TMR1CS<1:0> = 0x:
This bit is ignored. Timer1 uses the internal clock when TMR1CS<1:0> = 0x.
RD16: 16-Bit Read/Write Mode Enable bit
1 = Enables register read/write of Timer1 in one 16-bit operation
0 = Enables register read/write of Timer1 in two 8-bit operations
TMR1ON: Timer1 On bit
1 = Enables Timer1
0 = Stops Timer1
TMR1CS0
OSC
R/W-0
clock source should not be selected if the timer will be used with the ECCP capture/compare features.
T1CON: TIMER1 CONTROL REGISTER (ACCESS FCDh)
W = Writable bit
‘1’ = Bit is set
T1CKPS1
R/W-0
(2)
(2)
, Timer1 clock is from the T1CKI input pin
T1CKPS0
R/W-0
OSC
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
PIC18F46J50 FAMILY
T1OSCEN
OSC
Figure 12-1 displays a simplified block diagram of the
Timer1 module.
The module incorporates its own low-power oscillator
to provide an additional clocking option. The Timer1
oscillator can also be used as a low-power clock source
for the microcontroller in power-managed operation.
Timer1 is controlled through the T1CON Control
register (Register 12-1). It also contains the Timer1
oscillator Enable bit (T1OSCEN). Timer1 can be
enabled or disabled by setting or clearing control bit,
TMR1ON (T1CON<0>).
The F
be used with the ECCP capture/compare features. If the
timer will be used with the capture or compare features,
always select one of the other timer clocking options.
)
R/W-0
(1)
/4)
OSC
clock source (TMR1CS<1:0> = 01) should not
T1SYNC
R/W-0
x = Bit is unknown
R/W-0
RD16
DS39931C-page 193
TMR1ON
R/W-0
bit 0