C8051F526-IMR Silicon Labs, C8051F526-IMR Datasheet - Page 104
C8051F526-IMR
Manufacturer Part Number
C8051F526-IMR
Description
8-bit Microcontrollers - MCU 2KB 12ADC 125C LIN 10Pin MCU
Manufacturer
Silicon Labs
Datasheet
1.C8051F536-ITR.pdf
(220 pages)
Specifications of C8051F526-IMR
Product Category
8-bit Microcontrollers - MCU
Rohs
yes
Core
8051
Data Bus Width
8 bit
Maximum Clock Frequency
25 MHz
Program Memory Size
2 KB
Data Ram Size
256 B
On-chip Adc
Yes
Package / Case
DFN-10
Mounting Style
SMD/SMT
A/d Bit Size
12 bit
A/d Channels Available
6
Interface Type
SPI, UART
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 40 C
Number Of Programmable I/os
6
Number Of Timers
3
On-chip Dac
No
Processor Series
C8051
Program Memory Type
Flash
Factory Pack Quantity
1500
Supply Voltage - Max
2.7 V, 5.25 V
Supply Voltage - Min
2 V, 2.7 V
- Current page: 104 of 220
- Download datasheet (2Mb)
C8051F52x/F53x
10.5. External Interrupts
The INT0 and INT0 external interrupt sources are configurable as active high or low, edge or level sensi-
tive. The IN0PL (INT0 Polarity) and IN1PL (INT0 Polarity) bits in the IT01CF register select active high or
active low; the IT0 and IT1 bits in TCON (Section “18.1. Timer 0 and Timer 1” on page 182) select level or
edge sensitive. The table below lists the possible configurations.
INT0 and INT0 are assigned to Port pins as defined in the IT01CF register (see SFR Definition 10.5). Note
that INT0 and INT0 Port pin assignments are independent of any Crossbar assignments. INT0 and INT0
will monitor their assigned Port pins without disturbing the peripheral that was assigned the Port pin via the
Crossbar. To assign a Port pin only to INT0 and/or INT0, configure the Crossbar to skip the selected pin(s).
This is accomplished by setting the associated bit in register XBR0 (see Section “13.1. Priority Crossbar
Decoder” on page 122 for complete details on configuring the Crossbar).
In the typical configuration, the external interrupt pins should be skipped in the crossbar and configured as
open-drain with the pin latch set to 1. See Section “13. Port Input/Output” on page 120 for more informa-
tion.
IE0 (TCON.1) and IE1 (TCON.3) serve as the interrupt-pending flags for the INT0 and INT0 external inter-
rupts, respectively. If an INT0 or INT0 external interrupt is configured as edge-sensitive, the corresponding
interrupt-pending flag is automatically cleared by the hardware when the CPU vectors to the ISR. When
configured as level sensitive, the interrupt-pending flag remains logic 1 while the input is active as defined
by the corresponding polarity bit (IN0PL or IN1PL); the flag remains logic 0 while the input is inactive. The
external interrupt source must hold the input active until the interrupt request is recognized. It must then
deactivate the interrupt request before execution of the ISR completes or another interrupt request will be
generated.
104
IT0
1
1
0
0
IN0PL
0
1
0
1
Active high, edge sensitive
Active high, level sensitive
Active low, edge sensitive
Active low, level sensitive
INT0 Interrupt
Rev. 1.4
IT1
1
1
0
0
IN1PL
0
1
0
1
Active high, edge sensitive
Active high, level sensitive
Active low, edge sensitive
Active low, level sensitive
INT1 Interrupt
Related parts for C8051F526-IMR
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT EVALUATION FOR CP2102
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
KIT EVAL FOR CP2103 USB TO UART
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
KIT EVAL FOR CP2201 ETH CTRLR
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DAUGHTER CARD CAP TOUCH SENSE
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
KIT STARTER CAP TOUCH SENSE
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT FOR C8051F320/F321
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEVKIT-F120/21/22/23/24/25/26/27
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT FOR C8051F310/F311
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT F220/221/226/230/231/236
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT F300/301/302/303/304/305
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT FOR C8051F330/F331
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT FOR F005/006/007
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT FOR F020/F021/F022/F023
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
KIT DEV FOR C8051F34X
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
KIT DEV FOR C8051F41X
Manufacturer:
Silicon Laboratories Inc
Datasheet: