W25Q80BVSSIG Winbond Electronics, W25Q80BVSSIG Datasheet - Page 13

• Manufacturer Part Number: W25Q80BVSSIG
• Description: IC FLASH 8MBIT 8SOIC
• Manufacturer: Winbond Electronics

Specifications of W25Q80BVSSIG

• Format - Memory: FLASH
• Memory Type: FLASH
• Memory Size: 8M (1M x 8)
• Speed: 104MHz
• Interface: SPI Serial
• Voltage - Supply: 2.7 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (5.3mm Width), 8-SOP, 8-SOEIAJ
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: Q4816329; T1015683

9.1.6
The Complement Protect bit (CMP) is a non-volatile read/write bit in the status register (S14). It is used in
conjunction with SEC, TB, BP2, BP1 and BP0 bits to provide more flexibility for the array protection. Once
CMP is set to 1, previous array protection set by SEC, TB, BP2, BP1 and BP0 will be reversed. For
instance, when CMP=0, a top 4KB sector can be protected while the rest of the array is not; when
CMP=1, the top 4KB sector will become unprotected while the rest of the array become read-only. Please
refer to the Status Register Memory Protection table for details. The default setting is CMP=0.
9.1.7
The Status Register Protect bits (SRP1 and SRP0) are non-volatile read/write bits in the status register
(S8 and S7). The SRP bits control the method of write protection: software protection, hardware
protection, power supply lock-down or one time programmable (OTP) protection.
Notes:
1. When SRP1, SRP0 = (1, 0), a power-down, power-up cycle will change SRP1, SRP0 to (0, 0) state.
2. This feature is available upon special order. Please contact Winbond for details.
9.1.8
The Suspend Status bit is a read only bit in the status register (S15) that is set to 1 after executing a
Erase/Program Suspend (75h) instruction. The SUS status bit is cleared to 0 by Erase/Program Resume
(7Ah) instruction as well as a power-down, power-up cycle.
9.1.9
The Security Register Lock Bits (LB3, LB2, LB1) are non-volatile One Time Program (OTP) bits in Status
Register (S13, S12, S11) that provide the write protect control and status to the Security Registers. The
default state of LB[3:1] is 0, Security Registers are unlocked. LB[3:1] can be set to 1 individually using the
Write Status Register instruction. LB[3:1] are One Time Programmable (OTP), once it’s set to 1, the
corresponding 256-Byte Security Register will become read-only permanently.
SRP1
0
0
0
1
1
Complement Protect (CMP)
Status Register Protect (SRP1, SRP0)
Erase/Program Suspend Status (SUS)
Security Register Lock Bits (LB3, LB2, LB1)
SRP0
0
1
1
0
1
/WP
X
X
X
0
1
Power Supply
Unprotected
Lock-Down
Program
Protection
One Time
Hardware
Protected
Hardware
Register
Software
Status
(2)
Description
/WP pin has no control. The Status register can be written to
after a Write Enable instruction, WEL=1. [Factory Default]
When /WP pin is low the Status Register locked and can not
be written to.
When /WP pin is high the Status register is unlocked and can
be written to after a Write Enable instruction, WEL=1.
Status Register is protected and can not be written to again
until the next power-down, power-up cycle.
Status Register is permanently protected and can not be
written to.
- 13 -
Publication Release Date: October 06, 2010
W25Q80BV
(1)
Revision D