cp3cn23 National Semiconductor Corporation, cp3cn23 Datasheet - Page 30

• Manufacturer Part Number: cp3cn23
• Description: Cp3cn23 Reprogrammable Connectivity Processor With Dual Can Interfaces
• Manufacturer: National Semiconductor Corporation

www.national.com
7.2
The MSTAT register is a byte-wide, read-only register that
indicates the general status of the device. The MCFG regis-
ter format is shown below.
OENV2:0
PGMBUSY The Flash Programming Busy bit is automati-
DPGMBUSY The Data Flash Programming Busy indicates
WDRST
ISPRST
ISPRST WDRST Res. DPGMBUSY PGMBUSY OENV2:0
7
MODULE STATUS REGISTER (MSTAT)
6
The Operating Environment bits hold the
states sampled from the ENV[2:0] input pins
at reset. These states are controlled by exter-
nal hardware at reset and are held constant in
the register until the next reset.
cally set when either the program memory or
the data memory is being programmed or
erased. It is clear when neither of the memo-
ries is busy. When this bit is set, software must
not attempt to program or erase either of
these two memories. This bit is a copy of the
FMBUSY bit in the FMSTAT register.
0
1
that the flash data memory is being erased or
a pipelined programming sequence is current-
ly ongoing. Software must not attempt to per-
form any write access to the flash program
memory at this time, without also polling the
FSMSTAT.FMFULL bit in the flash memory in-
terface. The DPGMBUSY bit is a copy of the
FMBUSY bit in the FSMSTAT register.
0
1
The Watchdog Reset bit indicates that a
Watchdog timer reset has occurred. Write a 1
to this bit to clear it. Power-on reset also
clears this bit.
0
1
The Software ISP Reset bit indicates that a
software ISP reset has occurred since the bit
was last cleared. This bit is cleared by a
SWRESET(CLR) sequence or a power-on re-
set.
0
1
–
–
–
–
–
–
–
–
Flash memory is not busy.
Flash memory is busy.
Flash data memory is not busy.
Flash data memory is busy.
No Watchdog timer reset has occurred
since this bit was last cleared.
A Watchdog timer reset has occurred
since this bit was last cleared.
No software ISP reset has occurred since
this bit was last cleared.
A software ISP reset has occurred since
this bit was last cleared.
5
4
3
2
0
30
7.3
The SWRESET register is a byte-wide, write-only register
which provides a mechanism for software to initiate a reset
into ISP mode without regard to the status of the EMPTY
bits in the flash protection word. This form of reset is only al-
lowed when all of the following conditions are true:
T The device is in IRE or ERE mode
T BOOTAREA is defined (has a value other than 1111b) in
T ISPE is set in the flash protection word, indicating that
To initiate a reset under these conditions, it is necessary to
write the value E1h to the SWRESET register, followed with-
in 127 clock cycles by the value 3Eh. The reset then follows
immediately. This sequence is called SWRESET(ISP).
Once the device has been reset into ISP mode by SWRE-
SET(ISP), any subsequent reset (other than internal or ex-
ternal power-on reset) will cause the part to reset into ISP
mode because the EMPTY bits in the Protection Word con-
tinue to be ignored.
A second set of special values written to the SWRESET reg-
ister will cause a reset out of ISP mode (whether or not the
device is currently in ISP mode). This can be used as a sim-
ple software reset. In this case, no conditions are checked.
To initiate reset out of ISP mode, write the value E1h to the
SWRESET register, followed within 127 clock cycles by the
value 0Eh. The reset then follows immediately. This se-
quence is called SWRESET(CLR). This reset also cancels
the effect of any previous SWRESET(ISP), so subsequent
resets will check the EMPTY bits to determine whether to
enter ISP mode.
The ISP reset behaves similarly to the Watchdog reset, for
example, if the flash interface is busy when reset is assert-
ed, the reset to the clock module is delayed until the flash
operations are completed.
the Protection Word (see Section 8.4.2 for more details).
there is ISP code in the flash
SOFTWARE RESET REGISTER
(SWRESET)