LPC47M142-NC Standard Microsystems (SMSC), LPC47M142-NC Datasheet - Page 202

no-image

LPC47M142-NC

Manufacturer Part Number
LPC47M142-NC
Description
Manufacturer
Standard Microsystems (SMSC)
Datasheet

Specifications of LPC47M142-NC

Lead Free Status / RoHS Status
Not Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LPC47M142-NC
Manufacturer:
SMSC
Quantity:
55
Part Number:
LPC47M142-NC
Quantity:
1 715
Part Number:
LPC47M142-NC
Manufacturer:
SMSC
Quantity:
281
The LPC47M14x provides board test capability through the XNOR chain. When the chip is in the XNOR chain test
mode, setting the state of any of the input pins to the opposite of its current state will cause the output of the chain to
toggle.
All pins on the chip are inputs to the XNOR chain, with the exception of the following:
To put the chip in the XNOR chain test mode, tie LAD0 (pin 20) and LFRAME# (pin 24) low.
PCI_RESET# (pin 26) from a low to a high state. Once the chip is put into XNOR chain test mode, LAD0 (pin 20) and
LFRAME# (pin 24) become part of the chain.
To exit the XNOR chain test mode tie LAD0 (pin 20) or LFRAME# (pin 24) high. Then toggle PCI_RESET# (pin 26)
from a low to a high state. A VCC POR will also cause the XNOR chain test mode to be exited. To verify the test
mode has been exited, observe the output at TXD1 (pin 85). Toggling any of the input pins should not cause its state
to change.
Setup
Testing
SMSC DS – LPC47M14X
1)
2)
3)
4)
5)
1)
2)
3)
4)
1)
2)
3)
4)
5)
6)
7)
Warning: Ensure power supply is off during setup.
VCC (pins 53, 65, 93, & 125), VTR (pins 18, 113, & 122), and VREF (pin 44).
VSS (pins 7, 31, 60, 76, 101, 102, & 128) and AVSS (pin 40).
TXD1 (pin 85) This is the chain output.
nPCI_RESET (pin 26).
OCLK (pin 124)
Connect VSS (pins 7, 31, 60, 76, 101, 102, & 128) and AVSS (pin 40) to ground.
Connect VCC (pins 53, 65, 93, & 125), VTR (pins 18, 113, & 122), and VREF (pin 44)to VCC (3.3V).
Connect an oscilloscope or voltmeter to TXD1 (pin 85).
All other pins should be tied to ground.
Turn power on.
With LAD0 (pin 20) and LFRAME# (pin 24), low, bring PCI_RESET# (pin 26) high. The chip is now in XNOR
chain test mode. At this point, all inputs to the XNOR chain are low. The output, on TXD1 (pin 85), should
also be low. Refer to INITIAL CONFIG on Truth Table 1.
Bring pin 127 high. The output on TXD1 (pin 85) should go high. Refer to STEP ONE on Truth Table 1.
In descending pin order, bring each input high. The output should switch states each time an input is toggled.
Continue until all inputs are high. The output on TXD1 should now be low. Refer to END CONFIG on Truth
Table 1.
The current state of the chip is now represented by INITIAL CONFIG in Truth Table 2.
Each input should now be brought low, starting at pin one and continuing in ascending order. Continue until
all inputs are low. The output on TXD1 should now be low. Refer to Truth Table 2.
To exit test mode, tie LAD0 (pin 20) OR LFRAME# (pin 24) high, and toggle PCI_RESET# from a low to a
high state.
Page 202
Rev. 03/19/2001
Then toggle

Related parts for LPC47M142-NC