M1AFS250-FGG256I Actel Corporation, M1AFS250-FGG256I Datasheet - Page 322

• Manufacturer Part Number: M1AFS250-FGG256I
• Description: Actel Fusion Family Of Mixed Signal Fpgas
• Manufacturer: Actel Corporation

Datasheet Information
5 - 6
Revision
Advance 1.0
(continued)
The
In
changed to supply input.
The
following statement:
Actel recommends tying V
decouple V
The
In
were updated and note 2 is new.
The V
Input".
Table 2-48 • Uncalibrated Analog Channel Accuracy*
Table 2-49 • Calibrated Analog Channel Accuracy
Table 2-50 • Analog Channel Accuracy: Monitoring Standard Positive Voltages
new.
In
(x =
Hot-Swap changed to Standard
LVDS changed to Advanced
In
and AT (x =
Hot-Swap changed to Standard
LVDS changed to Advanced
In the title of
changed to Advanced I/O.
The title was changed from "Fusion Standard, LVDS, and Standard plus Hot-Swap
I/O" to
table headings were all updated. The heading used to be Standard and LVDS I/O
and was changed to Advanced I/O. Standard Hot-Swap was changed to just
Standard.
This sentence was deleted from the
The Standard hot-swap I/Os do not support slew rate control. In addition, these
references were changed:
• From: Fusion hot-swap I/O (Table 2-69 on page 2-122) To: Fusion Standard I/O
• From: Fusion LVDS I/O (Table 2-70 on page 2-122) To: Fusion Advanced I/O
The
In the title of
Hot-Swap was changed to Standard.
In the title of
Settings, LVDS was changed to Advanced.
In the title of
Standard
Table 2-47 • ADC Characteristics in Direct Input
Table 2-58 • Prescaler Op Amp Power-Down Truth Table—AV (x = 0), AC (x = 1),
Table 2-57 • Voltage Polarity Control Truth Table—AV (x = 0), AC (x = 1), and AT
"V
"V
"V
3)*, the following I/O Bank names were changed:
"Cold-Sparing Support" section
"V
CCNVM
CC33ACAP
CCPLA/B
COMPLA/B
CCPLA/B
Table 2-68 • Fusion Standard and Advanced I/O
Applications, LVDS was changed to Advanced.
CC
3), the following I/O Bank names were changed:
Table 2-76 • Fusion Advanced I/O Standards—SLEW and OUT_DRIVE
Flash Memory Block Power Supply (1.5 V)"
Table 2-64 • I/O Standards Supported by Bank
Table 2-75 • Fusion Standard I/O Standards—OUT_DRIVE
noise from PLL.
Table 2-81 • Fusion Standard and Advanced I/O Attributes vs. I/O
PLL Supply Voltage" section
PLL Supply Voltage"
Ground for West and East PLL" section
signal name was changed to
CCPLX
to V
was significantly updated.
"Slew Rate Control and Drive Strength"
R e vi s i o n 1
Changes
pin description was updated to include the
CC
is new.
and using proper filtering circuits to
"XTAL1 Crystal Oscillator Circuit
1,2,3
Mode, the commercial conditions
is new.
is new.
was updated.
Features. In addition, the
section, supply was
Type, LVDS I/O was
Settings,
section:
is
2-225
2-224
2-225
2-225
2-121
2-228
2-123
2-124
2-125
2-131
2-132
2-134
2-136
2-152
2-143
2-153
2-153
2-157
Page