S71GS128NB0 SPANSION [SPANSION], S71GS128NB0 Datasheet - Page 172
S71GS128NB0
Manufacturer Part Number
S71GS128NB0
Description
128N based MCPs
Manufacturer
SPANSION [SPANSION]
Datasheet
1.S71GS128NB0.pdf
(195 pages)
- Current page: 172 of 195
- Download datasheet (3Mb)
172
Page Mode READ Operation
Burst-Mode Operation
Summary
When a CellularRAM device is configured for page mode operation, the address
inputs are used to accelerate read accesses and cannot be used by the on-chip
circuitry to schedule refresh. If CE# is LOW longer than the t
of 4µs during a READ operation, the system must allow t
otherwise be expected) for all subsequent intrapage accesses until CE# goes
HIGH.
When configured for burst-mode operation, it is necessary to allow the device to
perform a refresh within any 4µs window. One of two conditions will enable the
device to schedule a refresh within 4µs. The first condition is when all burst op-
erations complete within 4µs. A burst completes when the CE# signal is
registered HIGH on a rising clock edge. The second condition that allows a refresh
is when a burst access crosses a row boundary. The row-boundary crossing
causes WAIT to be asserted while the next row is accessed and enables the
scheduling of refresh.
CellularRAM products are designed to ensure that any possible asynchronous tim-
ings do not cause data corruption due to lack of refresh. Slow bus timings on
asynchronous WRITE operations require that t
bus timings during asynchronous page READ operations cause the next intrapage
READ data to be delayed to t
Burst mode timings must allow the device to perform a refresh within any 4µs
period. A burst operation must either complete (CE# registered HIGH) or cross a
row boundary within 4µs to ensure successful refresh scheduling. These timing
requirements are likely to have little or no impact when interfacing a CellularRAM
device with a low-speed memory bus.
ADDRESS
LB#/UB#
DATA-IN
WE#
CE#
Figure 63. Extended WRITE Operation
A d v a n c e
AA
CellularRAM Type 2
.
t CEM or t TM > 4µs
I n f o r m a t i o n
t WP > t WC (MIN)
t DW > t WC (MIN)
WP
and t
DW
AA
be lengthened. Slow
CEM
(not t
maximum time
APA
, as would
cellRAM_00_A0 October 4, 2004
Related parts for S71GS128NB0
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
TS 48/CIVIL/1-BIT ECC, X8 I/O AND 3V VCC SPANSION SLC NAND
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
TS 48/CIVIL/1-BIT ECC, X8 I/O AND 3V VCC SPANSION SLC NAND
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
MBM29F400TC-70PFTNSPANSION [FLASH MEMORY CMOS 4M (512K x 8/256K x 16) BIT]
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
AM29F010B70JI1 Megabit (128 K x 8-bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
S29AL016D70BAI02016 MEGABIT CMOS 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
S29AL016M90FAI01016 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
S29AL016M90FAI02016 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet: